LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry LE, FWD >> Repair and Diagnosis >> Restraints >> Seat Belts >> Seat Belt Warning System - Diagnostics & Symptom Tests (Except Hybrid) >> Seat Belt Warning System >> Data List / Active Test [03/2017 - ] >> Data List / Active Test [03/2017 - ]

Data List / Active Test [03/2017 - ]

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter, Occupant Detection, SRS Airbag or Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Rear Right Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt RH buckle signal ON or OFF OFF: Rear RH seat belt fastened
      ON: Rear RH seat belt not fastened      		 -
      Rear Left Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for LH) buckle signal ON or OFF OFF: Rear LH seat belt (for LH) fastened
      ON: Rear LH seat belt (for LH) not fastened      		 -
      Rear Center Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for center) buckle signal ON or OFF OFF: Rear LH seat belt (for center) fastened
      ON: Rear LH seat belt (for center) not fastened      		 -
      Driver Seatbelt Warning Buzzer Function Driver seat belt warning buzzer ON or OFF Customized setting displayed -
      Passenger Seatbelt Warning Buzzer Function Front passenger seat belt warning buzzer ON or OFF Customized setting displayed -
      Rear Right Seatbelt Warning Buzzer Function Rear RH seat belt warning buzzer ON or OFF Customized value displayed -
      Rear Left Seatbelt Warning Buzzer Function Rear LH seat belt warning buzzer ON or OFF Customized value displayed -
      Rear Center Seatbelt Warning Buzzer Function Rear center seat belt warning buzzer ON or OFF Customized value displayed -

      Body Electrical > Occupant Detection > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Passenger Buckle SW Front passenger buckle switch Unset, Set or NG Unset: Seat belt not fastened
      Set: Seat belt fastened
      NG: Data is not determined      		 -

      Body Electrical > SRS Airbag > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Left side Buckle SW LH buckle switch Unset, Set or NG Unset: Seat belt not fastened
      Set: Seat belt fastened
      NG: Data is not determined      		 -
      Right side Buckle SW RH buckle switch Unset, Set or NG Unset: Seat belt not fastened
      Set: Seat belt fastened
      NG: Data is not determined      		 -

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RR Door Courtesy SW Rear door courtesy light switch RH ON or OFF ON: Rear door RH open
      OFF: Rear door RH closed      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH ON or OFF ON: Rear door LH open
      OFF: Rear door LH closed      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    5. Perform the Active Test according to the display on the Techstream.

      Body Electrical > Combination Meter > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Buzzer Operation (800Hz, Vol L, W/ Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Large
      • Fading tone
      		 ON -
      Buzzer Operation (800Hz, Vol L, W/O Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Large
      • Continuous tone
      		 ON -
      Buzzer Operation (800Hz, Vol S, W/ Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Small
      • Fading tone
      		 ON -
      Buzzer Operation (800Hz, Vol S, W/O Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Small
      • Continuous tone
      		 ON -
      Driver Side Seat Belt Warning Driver side seat belt warning light OFF/ON -
      Passenger Side Seat Belt Warning Front passenger side seat belt warning light OFF/ON Not applicable to this vehicle
      Rear Seat Belt Warning Rear seat belt warning light OFF/ON -
scientia non olet · About LEMON Manuals