Removal [06/2017 - 10/2020]: Procedure
- PRECAUTION NOTE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Refer to PRECAUTION [06/2017 - 09/2019] , or refer to PRECAUTION [09/2019 - 03/2020] , or refer to PRECAUTION [03/2020 - ]
- DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
For A25A-FKS:
Refer to PROCEDURE - Step 2 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 2 [08/2018 - 10/2020]
For 2GR-FKS:
Refer to PROCEDURE - Step 2
- REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 3 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 3 [08/2018 - 10/2020]
- REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Refer to PROCEDURE - Step 4 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 4 [08/2018 - 10/2020]
- REMOVE REAR ARMREST ASSEMBLY
Refer to PROCEDURE - Step 5 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 5 [08/2018 - 10/2020]
- REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Refer to PROCEDURE - Step 6 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 6 [08/2018 - 10/2020]
- REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Refer to PROCEDURE - Step 7 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 7 [08/2018 - 10/2020]
- REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Refer to PROCEDURE - Step 8 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 8 [08/2018 - 10/2020]
- REMOVE REAR DOOR SERVICE HOLE COVER
Refer to PROCEDURE - Step 12 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 12 [08/2018 - 10/2020]
- REMOVE REAR DOOR NO. 1 VENT SEAL
Refer to PROCEDURE - Step 13 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 13 [08/2018 - 10/2020]
- REMOVE REAR DOOR PANEL PROTECTOR
Refer to PROCEDURE - Step 14 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 14 [08/2018 - 10/2020]
- REMOVE REAR DOOR GLASS RUN
Refer to PROCEDURE - Step 15 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 15 [08/2018 - 10/2020]
- DISCONNECT REAR DOOR WEATHERSTRIP
- Disconnect the rear door weatherstrip until the screw of the rear door rear lower window frame sub-assembly is visible.
- REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Refer to PROCEDURE - Step 18 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 18 [08/2018 - 10/2020]
- REMOVE REAR DOOR QUARTER WINDOW GLASS
Refer to PROCEDURE - Step 19 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 19 [08/2018 - 10/2020]
- REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Refer to PROCEDURE - Step 20 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 20 [08/2018 - 10/2020]
- REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
- Using a T30 "TORX" socket wrench, remove the 3 screws.
*a Release Plate Remove in this Direction - Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
- When reusing the rear door lock with motor assembly:
- Using a T30 "TORX" socket wrench, remove the 3 screws.
- REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY
- REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
- REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY