LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry LE, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Navigation System - Diagnostic Codes & Symptom Tests (1 Of 2) (Except Hybrid) >> Navigation System >> DTC B1324: Lost Communication with Meter; DTC B1325: Lost Communication with HUD [06/2017 - ] >> Procedure

DTC B1324: Lost Communication with Meter; DTC B1325: Lost Communication with HUD [06/2017 - ]: Procedure

  1. CHECK DTC 
    1. Check for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTC B1324 and B1325 are not output A
      DTC B1324 and B1325 are output B
      DTC B1324 is output C
      DTC B1325 is output D

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2017 - 08/2018]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2018 - 09/2019]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2019 - 03/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2020 - 10/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2020 - 08/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2021 - ] 

    Result: 

    C 

    See step  11

    Result: 

    D 

    See step  16

    Result: 

    B 

    See step  2

  2. CHECK LOCAL BUS 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-9 - K125-20 Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Result Proceed to
      OK A
      NG (Below 54 Ω) B
      NG (70 Ω or higher) C

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2017 - 08/2018]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2018 - 09/2019]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2019 - 03/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2020 - 10/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2020 - 08/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2021 - ] 

    Result: 

    C 

    See step  9

    Result: 

    B 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-9 - K125-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  8

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-10 - K125-21 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-11 - K125-22 Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 17 JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the p1 headup display (meter mirror sub-assembly) connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      p1-14 (TX+) - p1-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY). Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  7. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K21 combination meter assembly connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K21-36 (TX+) - K21-37 (TX-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  DISASSEMBLY [03/2017 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K2 radio and display receiver assembly connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-5 (CNH1) - K2-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  9. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K2 radio and display receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-5 (CNH1) - K2-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    See step  10

  10. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Connect the K2 radio and display receiver assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-9 - K125-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 17 JUNCTION CONNECTOR 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  11. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) 
    1. Disconnect the K21 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K21-21 (ES) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      K21-40 (B) - Body ground Always 11 to 14 V
      K21-39 (IG+) - Body ground Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  12

  12. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Connect the K21 combination meter assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-10 - K125-21 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  15

    Result: 

    OK 

    See step  13

  13. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-9 - K125-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 17 JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K2 radio and display receiver assembly connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-5 (CNH1) - K2-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  15. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K21 combination meter assembly connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K21-36 (TX+) - K21-37 (TX-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  DISASSEMBLY [03/2017 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  16. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE) 
    1. Disconnect the p1 headup display (meter mirror sub-assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      p1-15 (TX-) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      p1-2 (B) - Body ground Always 11 to 14 V
      p1-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Connect the p1 headup display (meter mirror sub-assembly) connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-11 - K125-22 Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  20

    Result: 

    OK 

    See step  18

  18. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K125 No. 17 junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K125-9 - K125-20 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 17 JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  19

  19. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K2 radio and display receiver assembly connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-5 (CNH1) - K2-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  20. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 17 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the p1 headup display (meter mirror sub-assembly) connector.
    3. Connect the K125 No. 17 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      p1-14 (TX+) - p1-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY). Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals