LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry LE, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System - Diagnostic Codes (1 Of 2) (Except Hybrid) >> Audio And Visual System >> DTC B15C3: Speaker Output Short [06/2017 - 08/2018] >> Procedure

DTC B15C3: Speaker Output Short [06/2017 - 08/2018]: Procedure

  1. CHECK MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for 6 Speakers (w/ Manual (SOS) Switch) A
      for 6 Speakers (w/o Manual (SOS) Switch) B
      for 9 Speakers (w/ Manual (SOS) Switch) C
      for 9 Speakers (w/o Manual (SOS) Switch) D

    Result: 

    B 

    See step  5

    Result: 

    C 

    See step  10

    Result: 

    D 

    See step  13

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) 
    1. Disconnect the K4 radio and display receiver assembly connector.
    2. Disconnect the K12 DCM (telematics transceiver) connector.
    3. Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
    4. Disconnect the Q1 and P1 rear speaker assembly connectors.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-1 (FR+) or K12-2 (SPI+) - Body ground Always 10 kΩ or higher
      K4-6 (FR-) or K12-3 (SPI-) - Body ground Always 10 kΩ or higher
      K4-2 (FL+) or K8-4 (TWL+) - Body ground Always 10 kΩ or higher
      K4-7 (FL-) or K8-2 (TWL-) - Body ground Always 10 kΩ or higher
      K4-4 (RR+) or P1-1 - Body ground Always 10 kΩ or higher
      K4-9 (RR-) or P1-2 - Body ground Always 10 kΩ or higher
      K4-3 (RL+) or Q1-1 - Body ground Always 10 kΩ or higher
      K4-8 (RL-) or Q1-2 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND) 
    1. Disconnect the K12 DCM (telematics transceiver) connector.
    2. Disconnect the K7 front No. 2 speaker assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K12-5 (SPO+) or K7-4 (TWR+) - Body ground Always 10 kΩ or higher
      K12-6 (SPO-) or K7-2 (TWR-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [03/2017 - 09/2019]

    2. Measure the resistance according to the value(s) in the table below.
      GTY450683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  6

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [03/2017 - 09/2019] 

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR SPEAKERS - BODY GROUND) 
    1. Disconnect the K4 radio and display receiver assembly connector.
    2. Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
    3. Disconnect the Q1 and P1 rear speaker assembly connectors.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-1 (FR+) or K7-4 (TWR+) - Body ground Always 10 kΩ or higher
      K4-6 (FR-) or K7-2 (TWR-) - Body ground Always 10 kΩ or higher
      K4-2 (FL+) or K8-4 (TWL+) - Body ground Always 10 kΩ or higher
      K4-7 (FL-) or K8-2 (TWL-) - Body ground Always 10 kΩ or higher
      K4-4 (RR+) or P1-1 - Body ground Always 10 kΩ or higher
      K4-9 (RR-) or P1-2 - Body ground Always 10 kΩ or higher
      K4-3 (RL+) or Q1-1 - Body ground Always 10 kΩ or higher
      K4-8 (RL-) or Q1-2 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
    2. Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N1-2 or K7-3 (+) - Body ground Always 10 kΩ or higher
      N1-1 or K7-1 (-) - Body ground Always 10 kΩ or higher
      O1-2 or K8-3 (+) - Body ground Always 10 kΩ or higher
      O1-1 or K8-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [03/2017 - 09/2019]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - 09/2019] 

    Result: 

    OK 

    See step  8

  8. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [06/2017 - 08/2018]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

    Result: 

    OK 

    See step  9

  9. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020] 

  10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the K12 DCM (telematics transceiver) connector.
    3. Disconnect the K95 front No. 2 speaker assembly connector.
    4. Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
    5. Disconnect the P1 and Q1 rear speaker assembly connectors.
    6. Disconnect the R1 rear stereo component speaker assembly connector.
    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-14 (TWR+) or K12-2 (SPI+) - Body ground Always 10 kΩ or higher
      K14-29 (TWR-) or K12-3 (SPI-) - Body ground Always 10 kΩ or higher
      K14-12 (TWL+) or K95-2 (TWL+) - Body ground Always 10 kΩ or higher
      K14-27 (TWL-) or K95-1 (TWL-) - Body ground Always 10 kΩ or higher
      K14-15 (FR+) or K109-4 (+TW) - Body ground Always 10 kΩ or higher
      K14-30 (FR-) or K109-2 (-TW) - Body ground Always 10 kΩ or higher
      K14-13 (FL+) or K110-4 (+TW) - Body ground Always 10 kΩ or higher
      K14-28 (FL-) or K110-2 (-TW) - Body ground Always 10 kΩ or higher
      K14-11 (RR+) or P1-1 - Body ground Always 10 kΩ or higher
      K14-26 (RR-) or P1-2 - Body ground Always 10 kΩ or higher
      K14-9 (RL+) or Q1-1 - Body ground Always 10 kΩ or higher
      K14-24 (RL-) or Q1-2 - Body ground Always 10 kΩ or higher
      K14-10 (WF1+) or R1-4 (WF1+) - Body ground Always 10 kΩ or higher
      K14-25 (WF1-) or R1-3 (WF1-) - Body ground Always 10 kΩ or higher
      K14-8 (WF2+) or R1-2 (WF2+) - Body ground Always 10 kΩ or higher
      K14-23 (WF2-) or R1-1 (WF2-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  11

  11. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND) 
    1. Disconnect the K12 DCM (telematics transceiver) connector.
    2. Disconnect the K94 front No. 2 speaker assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K12-5 (SPO+) or K94-2 (TWR+) - Body ground Always 10 kΩ or higher
      K12-6 (SPO-) or K94-1 (TWR-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  12

  12. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [03/2017 - 09/2019]

    2. Measure the resistance according to the value(s) in the table below.
      GTY450683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  14

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [03/2017 - 09/2019] 

  13. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY OR SPEAKERS - BODY GROUND) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
    3. Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
    4. Disconnect the P1 and Q1 rear speaker assembly connectors.
    5. Disconnect the R1 rear stereo component speaker assembly connector.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-15 (FR+) or K109-4 (+TW) - Body ground Always 10 kΩ or higher
      K14-30 (FR-) or K109-2 (-TW) - Body ground Always 10 kΩ or higher
      K14-13 (FL+) or K110-4 (+TW) - Body ground Always 10 kΩ or higher
      K14-28 (FL-) or K110-2 (-TW) - Body ground Always 10 kΩ or higher
      K14-14 (TWR+) or K94-2 (TWR+) - Body ground Always 10 kΩ or higher
      K14-29 (TWR-) or K94-1 (TWR-) - Body ground Always 10 kΩ or higher
      K14-12 (TWL+) or K95-2 (TWL+) - Body ground Always 10 kΩ or higher
      K14-27 (TWL-) or K95-1 (TWL-) - Body ground Always 10 kΩ or higher
      K14-11 (RR+) or P1-1 - Body ground Always 10 kΩ or higher
      K14-26 (RR-) or P1-2 - Body ground Always 10 kΩ or higher
      K14-9 (RL+) or Q1-1 - Body ground Always 10 kΩ or higher
      K14-24 (RL-) or Q1-2 - Body ground Always 10 kΩ or higher
      K14-10 (WF1+) or R1-4 (WF1+) - Body ground Always 10 kΩ or higher
      K14-25 (WF1-) or R1-3 (WF1-) - Body ground Always 10 kΩ or higher
      K14-8 (WF2+) or R1-2 (WF2+) - Body ground Always 10 kΩ or higher
      K14-23 (WF2-) or R1-1 (WF2-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 3 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
    2. Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N1-2 or K109-3 (+) - Body ground Always 10 kΩ or higher
      N1-1 or K109-1 (-) - Body ground Always 10 kΩ or higher
      O1-2 or K110-3 (+) - Body ground Always 10 kΩ or higher
      O1-1 or K110-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  15

  15. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [03/2017 - 09/2019]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - 09/2019] 

    Result: 

    OK 

    See step  16

  16. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

    Result: 

    OK 

    See step  17

  17. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [06/2017 - 08/2018]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

    Result: 

    OK 

    See step  18

  18. INSPECT REAR STEREO COMPONENT SPEAKER ASSEMBLY 
    1. Remove the rear stereo component speaker assembly.

      Refer to REMOVAL [06/2017 - 10/2020]

    2. Inspect the rear stereo component speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR STEREO COMPONENT SPEAKER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020] 

    Result: 

    OK 

    See step  19

  19. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [06/2017 - ]

    2. Inspect the front No. 3 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020] 

scientia non olet · About LEMON Manuals