LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry LE, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System - Circuit Tests (2 Of 2) (Except Hybrid) >> Audio And Visual System >> Speaker Circuit [09/2019 -] >> Procedure

Speaker Circuit [09/2019 -]: Procedure

  1. CHECK MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for 6 Speakers A
      for 9 Speakers B

    Result: 

    B 

    See step  10

    Result: 

    A 

    See step  2

  2. CHECK SPEAKER (OPERATION CHECK) 
    1. Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
      GTY452678Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to OPERATION CHECK [09/2019 - 10/2020] , or refer to OPERATION CHECK [10/2020 - ]

    2. Perform the operation check above and determine the speaker that is not operating.

      Result

      Not Operating Speaker Proceed to
      Front No. 1 speaker assembly or front No. 2 speaker assembly
      (w/o Manual (SOS) Switch)      		 A
      Front No. 1 speaker assembly or front No. 2 speaker assembly
      (w/ Manual (SOS) Switch)      		 B
      Rear speaker assembly C

      HINT: 

      If sound cannot be heard from any speaker, inspect all of them.

    Result: 

    B 

    See step  4

    Result: 

    C 

    See step  8

    Result: 

    A 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) 
    1. Disconnect the K4 radio and display receiver assembly connector.
    2. Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
    3. Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
    4. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-1 (FR+) - K7-4 (TWR+) Always Below 1 Ω
      K4-6 (FR-) - K7-2 (TWR-) Always Below 1 Ω
      K4-2 (FL+) - K8-4 (TWL+) Always Below 1 Ω
      K4-7 (FL-) - K8-2 (TWL-) Always Below 1 Ω
      N1-2 - K7-3 (+) Always Below 1 Ω
      N1-1 - K7-1 (-) Always Below 1 Ω
      O1-2 - K8-3 (+) Always Below 1 Ω
      O1-1 - K8-1 (-) Always Below 1 Ω
      K4-1 (FR+) or K7-4 (TWR+) - Body ground Always 10 kΩ or higher
      K4-6 (FR-) or K7-2 (TWR-) - Body ground Always 10 kΩ or higher
      K4-2 (FL+) or K8-4 (TWL+) - Body ground Always 10 kΩ or higher
      K4-7 (FL-) or K8-2 (TWL-) - Body ground Always 10 kΩ or higher
      N1-2 or K7-3 (+) - Body ground Always 10 kΩ or higher
      N1-1 or K7-1 (-) - Body ground Always 10 kΩ or higher
      O1-2 or K8-3 (+) - Body ground Always 10 kΩ or higher
      O1-1 or K8-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  6

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) 
    1. Disconnect the K4 radio and display receiver assembly connector.
    2. Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
    3. Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
    4. Disconnect the K139 DCM (telematics transceiver) connector.
    5. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-1 (FR+) - K139-1 (SPI+) Always Below 1 Ω
      K4-6 (FR-) - K139-2 (SPI-) Always Below 1 Ω
      K139-3 (SPO+) - K7-4 (TWR+) Always Below 1 Ω
      K139-4 (SPO-) - K7-2 (TWR-) Always Below 1 Ω
      K4-2 (FL+) - K8-4 (TWL+) Always Below 1 Ω
      K4-7 (FL-) - K8-2 (TWL-) Always Below 1 Ω
      N1-2 - K7-3 (+) Always Below 1 Ω
      N1-1 - K7-1 (-) Always Below 1 Ω
      O1-2 - K8-3 (+) Always Below 1 Ω
      O1-1 - K8-1 (-) Always Below 1 Ω
      K4-1 (FR+) or K139-1 (SPI+) - Body ground Always 10 kΩ or higher
      K4-6 (FR-) or K139-2 (SPI-) - Body ground Always 10 kΩ or higher
      K4-2 (FL+) or K8-4 (TWL+) - Body ground Always 10 kΩ or higher
      K4-7 (FL-) or K8-2 (TWL-) - Body ground Always 10 kΩ or higher
      K139-3 (SPO+) or K7-4 (TWR+) - Body ground Always 10 kΩ or higher
      K139-4 (SPO-) or K7-2 (TWR-) - Body ground Always 10 kΩ or higher
      N1-2 or K7-3 (+) - Body ground Always 10 kΩ or higher
      N1-1 or K7-1 (-) - Body ground Always 10 kΩ or higher
      O1-2 or K8-3 (+) - Body ground Always 10 kΩ or higher
      O1-1 or K8-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [09/2019 - 10/2020] , or refer to REMOVAL [10/2020 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY843487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (SPI+) - 3 (SPO+) Always Below 1 Ω
      2 (SPI-) - 4 (SPO-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher
      1 (SPI+) or 3 (SPO+) - Body ground Always 10 kΩ or higher
      2 (SPI-) or 4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [09/2019 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

    Result: 

    OK 

    See step  6

  6. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [09/2019 - ]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2019 - ] 

    Result: 

    OK 

    See step  7

  7. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      OK

      Malfunction disappears.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

  8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) 
    1. Disconnect the K4 radio and display receiver assembly connector.
    2. Disconnect the Q7 and P7 rear speaker assembly connectors.
    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-4 (RR+) - P7-2 Always Below 1 Ω
      K4-9 (RR-) - P7-1 Always Below 1 Ω
      K4-3 (RL+) - Q7-2 Always Below 1 Ω
      K4-8 (RL-) - Q7-1 Always Below 1 Ω
      K4-4 (RR+) or P7-2 - Body ground Always 10 kΩ or higher
      K4-9 (RR-) or P7-1 - Body ground Always 10 kΩ or higher
      K4-3 (RL+) or Q7-2 - Body ground Always 10 kΩ or higher
      K4-8 (RL-) or Q7-1 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [09/2019 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

  10. CHECK SPEAKER (OPERATION CHECK) 
    1. Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
      GTY452678Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to OPERATION CHECK [09/2019 - 10/2020] , or refer to OPERATION CHECK [10/2020 - ]

    2. Perform the operation check above and determine the speaker that is not operating.

      Result

      Not Operating Speaker Proceed to
      Front No. 1 speaker assembly or front No. 3 speaker assembly A
      Front No. 2 speaker assembly
      (w/ Manual (SOS) Switch)      		 B
      Front No. 2 speaker assembly
      (w/o Manual (SOS) Switch)      		 C
      Rear speaker assembly D
      Rear stereo component speaker assembly E

      HINT: 

      If sound cannot be heard from any speaker, inspect all of them.

    Result: 

    B 

    See step  14

    Result: 

    C 

    See step  17

    Result: 

    D 

    See step  19

    Result: 

    E 

    See step  21

    Result: 

    A 

    See step  11

  11. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
    3. Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
    4. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-15 (FR+) - K109-4 (+TW) Always Below 1 Ω
      K14-30 (FR-) - K109-2 (-TW) Always Below 1 Ω
      K14-13 (FL+) - K110-4 (+TW) Always Below 1 Ω
      K14-28 (FL-) - K110-2 (-TW) Always Below 1 Ω
      N1-2 - K109-3 (+) Always Below 1 Ω
      N1-1 - K109-1 (-) Always Below 1 Ω
      O1-2 - K110-3 (+) Always Below 1 Ω
      O1-1 - K110-1 (-) Always Below 1 Ω
      K14-15 (FR+) or K109-4 (+TW) - Body ground Always 10 kΩ or higher
      K14-30 (FR-) or K109-2 (-TW) - Body ground Always 10 kΩ or higher
      K14-13 (FL+) or K110-4 (+TW) - Body ground Always 10 kΩ or higher
      K14-28 (FL-) or K110-2 (-TW) - Body ground Always 10 kΩ or higher
      N1-2 or K109-3 (+) - Body ground Always 10 kΩ or higher
      N1-1 or K109-1 (-) - Body ground Always 10 kΩ or higher
      O1-2 or K110-3 (+) - Body ground Always 10 kΩ or higher
      O1-1 or K110-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  12

  12. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [09/2019 - ]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [09/2019 - ] 

    Result: 

    OK 

    See step  13

  13. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [06/2017 - ]

    2. Inspect the front No. 3 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      OK

      Malfunction disappears.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

  14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 2 SPEAKER ASSEMBLY) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
    3. Disconnect the K139 DCM (telematics transceiver) connector.
    4. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-14 (TWR+) - K139-1 (SPI+) Always Below 1 Ω
      K14-29 (TWR-) - K139-2 (SPI-) Always Below 1 Ω
      K139-3 (SPO+) - K94-2 (TWR+) Always Below 1 Ω
      K139-4 (SPO-) - K94-1 (TWR-) Always Below 1 Ω
      K14-12 (TWL+) - K95-2 (TWL+) Always Below 1 Ω
      K14-27 (TWL-) - K95-1 (TWL-) Always Below 1 Ω
      K14-14 (TWR+) or K139-1 (SPI+) - Body ground Always 10 kΩ or higher
      K14-29 (TWR-) or K139-2 (SPI-) - Body ground Always 10 kΩ or higher
      K14-12 (TWL+) or K95-2 (TWL+) - Body ground Always 10 kΩ or higher
      K14-27 (TWL-) or K95-1 (TWL-) - Body ground Always 10 kΩ or higher
      K139-3 (SPO+) or K94-2 (TWR+) - Body ground Always 10 kΩ or higher
      K139-4 (SPO-) or K94-1 (TWR-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  15

  15. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

    Result: 

    OK 

    See step  16

  16. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [09/2019 - 10/2020] , or refer to REMOVAL [10/2020 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY843487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (SPI+) - 3 (SPO+) Always Below 1 Ω
      2 (SPI-) - 4 (SPO-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher
      1 (SPI+) or 3 (SPO+) - Body ground Always 10 kΩ or higher
      2 (SPI-) or 4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [09/2019 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

  17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-14 (TWR+) - K94-2 (TWR+) Always Below 1 Ω
      K14-29 (TWR-) - K94-1 (TWR-) Always Below 1 Ω
      K14-12 (TWL+) - K95-2 (TWL+) Always Below 1 Ω
      K14-27 (TWL-) - K95-1 (TWL-) Always Below 1 Ω
      K14-14 (TWR+) or K94-2 (TWR+) - Body ground Always 10 kΩ or higher
      K14-29 (TWR-) or K94-1 (TWR-) - Body ground Always 10 kΩ or higher
      K14-12 (TWL+) or K95-2 (TWL+) - Body ground Always 10 kΩ or higher
      K14-27 (TWL-) or K95-1 (TWL-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  18

  18. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

  19. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the P7 and Q7 rear speaker assembly connectors.
    3. Measure the resistance according to the value (s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-11 (RR+) - P7-2 Always Below 1 Ω
      K14-26 (RR-) - P7-1 Always Below 1 Ω
      K14-9 (RL+) - Q7-2 Always Below 1 Ω
      K14-24 (RL-) - Q7-1 Always Below 1 Ω
      K14-11 (RR+) or P7-2 - Body ground Always 10 kΩ or higher
      K14-26 (RR-) or P7-1 - Body ground Always 10 kΩ or higher
      K14-9 (RL+) or Q7-2 - Body ground Always 10 kΩ or higher
      K14-24 (RL-) or Q7-1 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  20

  20. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [03/2017 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [09/2019 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

  21. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR STEREO COMPONENT SPEAKER ASSEMBLY) 
    1. Disconnect the K14 stereo component amplifier assembly connector.
    2. Disconnect the R1 rear stereo component speaker assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K14-10 (WF1+) - R1-4 (WF1+) Always Below 1 Ω
      K14-25 (WF1-) - R1-3 (WF1-) Always Below 1 Ω
      K14-8 (WF2+) - R1-2 (WF2+) Always Below 1 Ω
      K14-23 (WF2-) - R1-1 (WF2-) Always Below 1 Ω
      K14-10 (WF1+) or R1-4 (WF1+) - Body ground Always 10 kΩ or higher
      K14-25 (WF1-) or R1-3 (WF1-) - Body ground Always 10 kΩ or higher
      K14-8 (WF2+) or R1-2 (WF2+) - Body ground Always 10 kΩ or higher
      K14-23 (WF2-) or R1-1 (WF2-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  22

  22. INSPECT REAR STEREO COMPONENT SPEAKER ASSEMBLY 
    1. Remove the rear stereo component speaker assembly.

      Refer to REMOVAL [06/2017 - 10/2020] , or refer to REMOVAL [10/2020 - ]

    2. Inspect the rear stereo component speaker assembly.

      Refer to INSPECTION [06/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 10/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [10/2020 - ] 

    Result: 

    NG 

    REPLACE REAR STEREO COMPONENT SPEAKER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020]  , or refer to  REMOVAL [10/2020 - ] 

scientia non olet · About LEMON Manuals