LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> C-HR XLE >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Air Conditioning System - Service Information (1 Of 3) >> Condenser >> Installation [02/2017 - 10/2017] >> Procedure

Installation [02/2017 - 10/2017]: Procedure

  1. INSTALL COOLER CONDENSER ASSEMBLY 
    1. Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.
      GTY761549Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Install in this Direction
      NOTE:

      Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.

      HINT: 

      If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.

      Capacity

      Add 40 cc (1.35 fl. oz)

      Compressor Oil

      VC100YF or equivalent

  2. CONNECT COOLER REFRIGERANT LIQUID PIPE A 
    1. Remove the vinyl tape from the cooler refrigerant liquid pipe A and cooler condenser assembly.
    2. Apply sufficient compressor oil to a new O-rings and fitting surfaces of the cooler refrigerant liquid pipe A

      Compressor Oil

      VC100YF or equivalent

    3. Install the O-ring to the air cooler refrigerant liquid pipe A.
      NOTE:

      Keep the O-rings and O-ring fitting surfaces free of foreign matter.

    4. Connect the cooler refrigerant liquid pipe A to the cooler condenser assembly with the bolt.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  3. CONNECT DISCHARGE HOSE SUB-ASSEMBLY 
    1. Remove the vinyl tape from the discharge hose sub-assembly and the connecting part of the cooler condenser assembly.
    2. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.

      Compressor Oil

      VC100YF or equivalent

    3. Install the O-ring to the discharge hose sub-assembly.
    4. Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  4. INSTALL NO. 1 RADIATOR AIR GUIDE LH 

    Refer to PROCEDURE - Step 1

  5. INSTALL NO. 1 RADIATOR AIR GUIDE RH 

    Refer to PROCEDURE - Step 2

  6. INSTALL FRONT BUMPER REINFORCEMENT 

    Refer to PROCEDURE - Step 8

  7. INSTALL FRONT BUMPER ENERGY ABSORBER 

    Refer to PROCEDURE - Step 11

  8. INSTALL NO. 2 RADIATOR AIR GUIDE 

    Refer to PROCEDURE - Step 17

  9. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 18

  10. INSTALL HOOD LOCK ASSEMBLY 

    Refer to PROCEDURE - Step 5

  11. INSTALL HOOD LOCK NUT CAP 

    Refer to PROCEDURE - Step 6

  12. INSTALL NO. 1 RADIATOR TO SUPPORT SEAL 

    Refer to PROCEDURE - Step 12

  13. INSTALL NO. 1 RADIATOR GRILLE RETAINER 

    Refer to PROCEDURE - Step 13

  14. INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 22

  15. INSTALL NO. 1 AIR CLEANER INLET 

    Refer to PROCEDURE - Step 23

  16. INSTALL HEADLIGHT ASSEMBLY LH 

    Refer to INSTALLATION [02/2017 - 10/2017]

  17. INSTALL HEADLIGHT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  18. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT 

    Refer to PROCEDURE - Step 2

  19. WARM UP WARM UP ENGINE 

    Refer to PROCEDURE - Step 3

  20. INSPECT FOR REFRIGERANT LEAK 

    Refer to PROCEDURE - Step 4

  21. ADJUST HOOD SUB-ASSEMBLY 

    Refer to ADJUSTMENT [02/2017 - ]

scientia non olet · About LEMON Manuals