LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> C-HR XLE >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> (Door / Hatch) - Service Information (1 Of 2) >> Back Door >> Disassembly [09/2019 - 12/2021] >> Procedure

Disassembly [09/2019 - 12/2021]: Procedure

  1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) 

    Refer to PROCEDURE - STEP 7 [09/2019 - 08/2020] , or refer to PROCEDURE - STEP 7 [08/2020 - 12/2021]

  2. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 

    Refer to PROCEDURE - STEP 8 [09/2019 - 08/2020] , or refer to PROCEDURE - STEP 8 [08/2020 - 12/2021]

  3. REMOVE BACK DOOR TRIM UPPER PANEL ASSEMBLY 
    1. Disengage the claws and clips to remove the back door trim upper panel assembly.
      GTY772011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE BACK DOOR SIDE GARNISH LH 
    1. Disengage the claws and clips to remove the back door side garnish LH.
      GTY756321Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE BACK DOOR SIDE GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  6. REMOVE PACKAGE TRAY TRIM GARNISH HOOK 

    HINT: 

    Use the same procedure for the RH side and LH side.

    1. Remove the screw.
      GTY756316Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the package tray trim garnish hook.
      GTY772009Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE BACK DOOR TRIM PANEL ASSEMBLY 
    1. Disengage the clips to remove the back door trim panel assembly.
      GTY756323Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE DOOR PULL HANDLE 
    1. Using a moulding remover D, disengage the claws to remove the door pull handle.
      GTY916692Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE NO. 1 BACK DOOR SERVICE HOLE COVER 
    1. Disengage the claws to remove the No. 1 back door service hole cover.
      GTY756319Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER 

    HINT: 

    Use the same procedure as for the No. 1 back door service hole cover.

  11. REMOVE NO. 3 BACK DOOR SERVICE HOLE COVER 
    1. Disengage the claws to remove the No. 3 back door service hole cover.
      GTY756320Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE BACK DOOR SERVICE HOLE COVER LH 
    1. Disengage the claws to remove the back door service hole cover LH.
      GTY772010Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE BACK DOOR SERVICE HOLE COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  14. REMOVE BACK DOOR LOCK COVER 
    1. Disengage the claws.
      GTY762550Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Double-sided Tape
    2. Remove the double-sided tape and back door lock cover.
      NOTE:

      Remove any remaining double-sided tape from the back door.

  15. REMOVE BACK DOOR LOCK ASSEMBLY 

    Refer to PROCEDURE - STEP 8

  16. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY 

    Refer to PROCEDURE - STEP 5

  17. REMOVE REAR WIPER MOTOR ASSEMBLY 

    Refer to PROCEDURE - STEP 7

  18. REMOVE REAR WIPER MOTOR GROMMET 

    Refer to PROCEDURE - STEP 6

  19. REMOVE BACK DOOR LOWER STOPPER 
    1. Remove the bolt.
      GTY756318Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide to remove the back door lower stopper.

      HINT: 

      Use the same procedure for the RH side and LH side.

  20. REMOVE REAR SPOILER ASSEMBLY 

    Refer to PROCEDURE - STEP 4

  21. REMOVE REAR WASHER NOZZLE 

    Refer to PROCEDURE - STEP 2

  22. REMOVE REAR LIGHT COVER LH (w/ Cover) 

    Refer to PROCEDURE - STEP 7

  23. REMOVE REAR LIGHT COVER RH (w/ Cover) 

    HINT: 

    Use the same procedure as for the LH side.

  24. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY 
  25. REMOVE BACK DOOR OPENER SWITCH ASSEMBLY 

    See step  2

  26. REMOVE LICENSE PLATE LIGHT ASSEMBLY 

    Refer to PROCEDURE - STEP 2

  27. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System) 

    Refer to PROCEDURE - STEP 2

  28. REMOVE NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System) 
    1. Disengage the claws to remove the No. 2 back door garnish retainer.
      GTY756120Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE BACK DOOR PANEL CUSHION 
    1. Disengage the claws to remove the 2 back door panel cushions.
      GTY756328Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. REMOVE NO. 2 BACK DOOR PANEL PROTECTOR 
    1. Disengage the clips.
      GTY752165Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Double-sided Tape
    2. Remove the double-sided tape and No. 2 back door panel protector.
      NOTE:

      Remove any remaining double-sided tape from the back door.

  31. REMOVE NO. 1 BACK DOOR PANEL PROTECTOR 

    HINT: 

    Use the same procedure for the No. 2 back door panel protector.

  32. REMOVE REAR LIGHT ASSEMBLY LH 

    Refer to PROCEDURE - STEP 2

  33. REMOVE REAR LIGHT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  34. REMOVE REAR LIGHT PACKING 

    Refer to PROCEDURE - STEP 3

  35. REMOVE HOLE PLUG 
    1. Remove the hole plug.
      GTY847308Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. REMOVE NO. 1 BACK DOOR NAME PLATE (w/ Brand Mark) 

    Refer to PROCEDURE - STEP 2

  37. REMOVE NO. 2 BACK DOOR NAME PLATE 

    Refer to PROCEDURE - STEP 1

  38. REMOVE NO. 1 BACK DOOR EMBLEM 

    Refer to PROCEDURE - STEP 3

scientia non olet · About LEMON Manuals