DTC C13A7: Actuator Malfunction [02/2017 - 05/2018]: Procedure

1. Check for DTCs.

   Refer to DTC CHECK / CLEAR [02/2017 - ]

   Chassis > ABS/VSC/TRAC/EPB > Trouble Codes 

   Result

   Result	Proceed to
   Only DTC C13A7/43 is output	A
   DTCs other than C13A7/43 are output	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [02/2017 - 05/2018] 

Result: 

A 

See step  2

1. Turn the ignition switch off.
2. Connect the Techstream to the DLC3.
3. Turn the ignition switch to ON.
4. Turn the Techstream on.
5. Enter the following menus: Chassis / Electric Parking Brake / Data List.
6. Read the Data List according to the display on the Techstream.

   Chassis > ABS/VSC/TRAC/EPB > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Permission of RH Interlocking PKB Lock	Parking brake actuator assembly RH parking brake lock control permission status	OK or NG	-	-
   Permission of LH Interlocking PKB Lock	Parking brake actuator assembly LH parking brake lock control permission status	OK or NG	-	-

   Chassis > ABS/VSC/TRAC/EPB > Data List 

   Tester Display
   Permission of RH Interlocking PKB Lock
   Permission of LH Interlocking PKB Lock

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the parking brake wire assembly.

   Refer to REMOVAL [02/2017 - 05/2018]

2. Check the parking brake wire assembly for damage.

   OK

   No damage.

   HINT: 

   If damaged, there may be a short in the wire harness or a short to ground.

3. Inspect the parking brake wire assembly.

   Standard Resistance

   RH
   
   

   Tester Connection	Condition	Specified Condition
   dM2-2 (MRR-) - d2-1 (MRR-)	Always	Below 1 Ω
   dM2-2 (MRR-) - d2-2 (MRR+)	Always	10 kΩ or higher
   dM2-2 (MRR-) or d2-1 (MRR-) - Body ground	Always	10 kΩ or higher
   dM2-1 (MRR+) - d2-2 (MRR+)	Always	Below 1 Ω
   dM2-1 (MRR+) - d2-1 (MRR-)	Always	10 kΩ or higher
   dM2-1 (MRR+) or d2-2 (MRR+) - Body ground	Always	10 kΩ or higher

   LH
   
   

   Tester Connection	Condition	Specified Condition
   eM2-2 (MRL-) - e2-1 (MRL-)	Always	Below 1 Ω
   eM2-2 (MRL-) - e2-2 (MRL+)	Always	10 kΩ or higher
   eM2-2 (MRL-) or e2-1 (MRL-) - Body ground	Always	10 kΩ or higher
   eM2-1 (MRL+) - e2-2 (MRL+)	Always	Below 1 Ω
   eM2-1 (MRL+) - e2-1 (MRL-)	Always	10 kΩ or higher
   eM2-1 (MRL+) or e2-2 (MRL+) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE PARKING BRAKE WIRE ASSEMBLY. Refer to  REMOVAL [02/2017 - 05/2018] 

Result: 

OK 

See step  4

1. Turn the ignition switch off.
2. Make sure the parking brake wire assembly is securely installed.
3. Disconnect the A42 skid control ECU (brake actuator assembly) connector.
4. Disconnect the d2 or e2 parking brake actuator assembly connector.
5. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   RH
   
   

   Tester Connection	Condition	Specified Condition
   A42-2 (MRR+) - d2-2 (MRR+)	Always	Below 1 Ω
   A42-3 (MRR-) - d2-1 (MRR-)	Always	Below 1 Ω
   A42-2 (MRR+) or d2-2 (MRR+) - Body ground	Always	10 kΩ or higher
   A42-3 (MRR-) or d2-1 (MRR-) - Body ground	Always	10 kΩ or higher

   LH
   
   

   Tester Connection	Condition	Specified Condition
   A42-13 (MRL+) - e2-2 (MRL+)	Always	Below 1 Ω
   A42-12 (MRL-) - e2-1 (MRL-)	Always	Below 1 Ω
   A42-13 (MRL+) or e2-2 (MRL+) - Body ground	Always	10 kΩ or higher
   A42-12 (MRL-) or e2-1 (MRL-) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  5

1. Enter rear brake pad replacement mode.

   Refer to TEST MODE PROCEDURE [02/2017 - ]

2. Turn the ignition switch off.
3. Check that the rotating parts are not seized or the actuator is not spinning freely.
   1. Check that the parking brake actuator assembly is installed properly to the rear brake caliper and that it is not spinning freely.

      For the parking brake actuator assembly removal procedure: Refer to REMOVAL [02/2017 - 05/2018]

   2. Check that there is no damage to the rotating parts from the parking brake actuator assembly to the rear brake caliper.
   3. Inspect the parking brake actuator assembly and check that it operates correctly.

      Refer to INSPECTION [02/2017 - ]

   4. Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.

      HINT: 

      For the check procedures, refer to the parking brake forced release method when not using the Techstream.

      Refer to OPERATION METHOD [02/2017 - 05/2018]

   HINT: 

   Return to normal mode after work is complete.

   Refer to TEST MODE PROCEDURE [02/2017 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY. Refer to  REMOVAL [02/2017 - 05/2018] 

Result: 

NG 

REPAIR OR REPLACE NECESSARY PARTS