LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> C-HR Limited >> Repair and Diagnosis >> Accessories & Equipment >> Headlights >> Automatic High Beam System - Diagnostic Codes & Symptom Tests >> Automatic High Beam System >> Automatic High Beam System does not Operate or Operation Indicator does not Illuminate [09/2019 - 08/2020] >> Procedure

Automatic High Beam System does not Operate or Operation Indicator does not Illuminate [09/2019 - 08/2020]: Procedure

  1. CHECK AUTOMATIC HIGH BEAM INDICATOR LIGHT 
    1. Check the operation of the automatic high beam indicator light.
      1. Turn the ignition switch to ON.
      2. Turn the light control switch to the AUTO or head position.
      3. Turn the headlight dimmer switch to the high position.
      4. Turn the automatic high beam main switch on.

      OK

      Automatic high beam indicator light illuminate.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  4

    Result: 

    OK 

    See step  2

  2. READ VALUE USING TECHSTREAM 
    GTY770871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *1 Forward Recognition Camera
    (Automatic High Beam Sensor)
    *2 Work Light or Equivalent
    *a 100 mm or less
    1. Shine a light on the automatic high beam sensor.

      HINT: 

      If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.

    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Main Body / Data List.
    6. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed Undetec: Undetected
      CAM NA: Camera detection malfunction*1
      No sens: No detection
      Hlight: Oncoming vehicles with headlights on
      Taillgt: Preceding vehicles with taillights on
      Speed: Vehicle speed
      Daytime: Daytime state
      Village: Urban area
      Malfunc: System delay
      1. *1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.

      Body Electrical > Main Body > Data List 

      Tester Display
      Auto H Beam STS0

      OK

      "Daytime" is displayed on the Techstream.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FORWARD RECOGNITION CAMERA. Refer to  REMOVAL [02/2017 - 08/2020] 

    Result: 

    OK 

    See step  3

  3. READ VALUE USING TECHSTREAM 
    GTY752756Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *1 Cardboard or Equivalent Object
    *a 150 mm or more
    *b 3 mm or more
    1. Cover the automatic high beam sensor with an opaque object, such as cardboard.
      NOTE:
      • Make sure that there is no clearance between the cardboard or equivalent object and the area of the windshield glass in front of the automatic high beam sensor.
      • If there is any clearance, light may shine on the automatic high beam sensor and the value of the Data List will not change.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Main Body / Data List.
    6. Read the Data List according to the display on the Techstream.

      HINT: 

      As it may take time for the values in the Data List to change, wait at least 10 seconds before reading the Data List.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed Undetec: Undetected
      CAM NA: Camera detection malfunction*1
      No sens: No detection
      Hlight: Oncoming vehicles with headlights on
      Taillgt: Preceding vehicles with taillights on
      Speed: Vehicle speed
      Daytime: Daytime state
      Village: Urban area
      Malfunc: System delay
      1. *1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.

      Body Electrical > Main Body > Data List 

      Tester Display
      Auto H Beam STS0

      OK

      "Speed" is displayed on the Techstream.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2019 - 08/2020] 

    Result: 

    NG 

    REPLACE FORWARD RECOGNITION CAMERA. Refer to  REMOVAL [02/2017 - 08/2020] 

  4. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto High Beam Main Switch Auto high beam switch signal OFF or ON ON: Auto high beam switch pressed
      OFF: Auto high beam switch not pressed      		 -

      Body Electrical > Main Body > Data List 

      Tester Display
      Auto High Beam Main Switch

      OK

      Normal conditions listed above are displayed.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  5

  5. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed Undetec: Undetected
      CAM NA: Camera detection malfunction*1
      No sens: No detection
      Hlight: Oncoming vehicles with headlights on
      Taillgt: Preceding vehicles with taillights on
      Speed: Vehicle speed
      Daytime: Daytime state
      Village: Urban area
      Malfunc: System delay
      1. *1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.

      Body Electrical > Main Body > Data List 

      Tester Display
      Auto H Beam STS0

      OK

      "Daytime" or "Speed" is displayed on the Techstream.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FORWARD RECOGNITION CAMERA. Refer to  REMOVAL [02/2017 - 08/2020] 

    Result: 

    OK 

    See step  6

  6. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    5. Perform the Active Test according to the display on the Techstream.

      Body Electrical > Combination Meter > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Automatic High Beam Indicator (Green) Automatic high beam indicator light OFF or ON -

      Body Electrical > Combination Meter > Active Test 

      Tester Display
      Automatic High Beam Indicator (Green)

      OK

      Automatic high beam indicator light illuminate.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [10/2017 - 08/2020] 

    Result: 

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [02/2017 - 08/2020] 

  7. INSPECT AUTO HIGH BEAM SWITCH 
    1. Remove the auto high beam switch.

      Refer to REMOVAL [02/2017 - ]

    2. Inspect the auto high beam switch.

      Refer to INSPECTION [02/2017 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE AUTO HIGH BEAM SWITCH. Refer to  REMOVAL [02/2017 - ] 

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND) 
    1. Disconnect the F16 main body ECU (multiplex network body ECU) connector.
    2. Measure the resistance according to the value(s) in the chart below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F6-6 (+B) - F16-17 (AHBI) Always Below 1 Ω
      F6-6 (+B) or F16-17 (AHBI) - Body ground Always 10 kΩ or higher
      F6-3 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [10/2017 - 08/2020] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals