LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 XLE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 169 (Front Power Seat Control System (HV, W/ Memory) - Diagnostic Codes & Symptom Tests (1 Of 2)) >> FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory) >> DTC B2650: Slide Sensor Malfunction [11/2018 - ] >> Procedure

DTC B2650: Slide Sensor Malfunction [11/2018 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CLEAR DTC 
    1. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [11/2018 - 10/2023] , or refer to DTC CHECK / CLEAR [10/2023 - 11/2024] , or refer to DTC CHECK / CLEAR [11/2024 - ]

      Body Electrical > Driver Seat > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  2

  2. CHECK FOR DTC 
    1. Check for DTCs.

      Refer to DTC CHECK / CLEAR [11/2018 - 10/2023] , or refer to DTC CHECK / CLEAR [10/2023 - 11/2024] , or refer to DTC CHECK / CLEAR [11/2024 - ]

      Body Electrical > Driver Seat > Trouble Codes 

      OK

      DTC B2650 is not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

    Result: 

    NG 

    See step  3

  3. PERFORM ACTIVE TEST USING TECHSTREAM (SEAT SLIDE OPERATION) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.
    5. Perform the Active Test according to the display on the Techstream.

      Body Electrical > Driver Seat > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Seat Slide Operation Seat slide operation OFF/Rear/Front -

      Body Electrical > Driver Seat > Active Test 

      Tester Display
      Seat Slide Operation

      OK

      Slide motor operates normally.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  6

    Result: 

    OK 

    See step  4

  4. CHECK POSITION CONTROL ECU ASSEMBLY (SLIDE MOTOR CIRCUIT) 
    1. Disconnect the slide motor (front seat adjuster assembly LH) connector.
      GTY915998Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Rear view of wire harness connector
      (to Slide Motor [Front Seat Adjuster Assembly LH])
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      T1-2 - T1-3 Slide switch on 4.8 to 5.1 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH) 

    Refer to DISASSEMBLY [11/2018 - 12/2021] , or refer to DISASSEMBLY [12/2021 - ]

    Result: 

    NG 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH]) 
    1. Disconnect the T8 position control ECU assembly connector.
    2. Disconnect the T1 slide motor (front seat adjuster assembly LH) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T8-26 (SSRS) - T1-2 Always Below 1 Ω
      T8-26 (SSRS) or T1-2 - Other terminals and body ground Always 10 kΩ or higher
      T8-12 (SGND) - T1-3 Always Below 1 Ω
      T8-12 (SGND) or T1-3 - Other terminals and body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE POSITION CONTROL ECU ASSEMBLY 

    Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH) 
    1. Remove the slide motor (front seat adjuster assembly LH).

      Refer to DISASSEMBLY [11/2018 - 12/2021] , or refer to DISASSEMBLY [12/2021 - ]

    2. Inspect the slide motor (front seat adjuster assembly LH).

      Refer to INSPECTION [11/2018 - 12/2021] , or refer to INSPECTION [12/2021 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY LH) 

    Refer to DISASSEMBLY [11/2018 - 12/2021] , or refer to DISASSEMBLY [12/2021 - ]

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY LH]) 
    1. Disconnect the T7 position control ECU assembly connector.
    2. Disconnect the T1 slide motor (front seat adjuster assembly LH) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      T7-1 (SLD+) - T1-4 Always Below 1 Ω
      T7-1 (SLD+) or T1-4 - Other terminals and body ground Always 10 kΩ or higher
      T7-5 (SLD-) - T1-1 Always Below 1 Ω
      T7-5 (SLD-) or T1-1 - Other terminals and body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE POSITION CONTROL ECU ASSEMBLY 

    Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals