LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 XLE, AWD >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Heating / Air Conditioning System - Service Information (4 Of 5) >> COMPRESSOR (for A25A-FXS) >> Removal [10/2019 - 06/2020] >> Procedure

Removal [10/2019 - 06/2020]: Procedure

  1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM 
    1. for HFC-134a (R134a):

      Refer to PROCEDURE - Step 1

    2. for HFO-1234yf (R1234yf):

      Refer to PROCEDURE - Step 1

  2. REMOVE SERVICE PLUG GRIP 

    Refer to REMOVAL [10/2019 - 06/2020]

  3. CHECK TERMINAL VOLTAGE 
    1. for AWD:
      1. Remove the No. 2 inverter protector.

        Refer to PROCEDURE - Step 8

    2. Disconnect the engine room main wire.

      Refer to PROCEDURE - Step 5

    3. Remove the connector cover assembly.
      1. for 2WD:

        Refer to PROCEDURE - Step 9

      2. for AWD:

        Refer to PROCEDURE - Step 10

    4. Check the terminal voltage.
      1. for 2WD:

        Refer to PROCEDURE - Step 10

      2. for AWD:

        Refer to PROCEDURE - Step 11

    5. Install the connector cover assembly.

      Refer to PROCEDURE - Step 7

    6. Connect the engine room main wire.

      Refer to PROCEDURE - Step 31

    7. for AWD:
      1. Install the No. 2 inverter protector.

        Refer to PROCEDURE - Step 16

  4. REMOVE FRONT WHEEL RH 

    Refer to REMOVAL [11/2018 - ]

  5. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH (for TMC Made) 

    HINT: 

    Use the same procedure described as for the LH side.

    Refer to PROCEDURE - Step 1

  6. REMOVE FRONT FENDER FRONT OUTSIDE MOULDING RH (for TMMC Made) 

    HINT: 

    Use the same procedure described as for the front fender moulding sub-assembly RH (for TMC Made).

  7. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 13

  8. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 14

  9. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 15

  10. REMOVE FRONT FENDER MUDGUARD RH (w/ Mudguard) 
    1. for Short Type:

      HINT: 

      Use the same procedure described as for the LH side.

      Refer to PROCEDURE - Step 1

    2. for Long Type:

      HINT: 

      Use the same procedure described as for the LH side.

      Refer to PROCEDURE - Step 3

  11. REMOVE FRONT FENDER APRON SEAL RH (for TMC Made) 

    Refer to PROCEDURE - Step 18

  12. REMOVE FRONT FENDER APRON SEAL RH (for TMMC Made) 

    HINT: 

    Use the same procedure described as for the front fender apron seal RH (for TMC Made).

  13. REMOVE FRONT FENDER LINER RH 

    Refer to PROCEDURE - Step 8

  14. DISCONNECT SUCTION HOSE SUB-ASSEMBLY 
    1. Remove the bolt and disconnect the suction hose sub-assembly.
      GTY839021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not apply excessive force to the suction hose sub-assembly.

    2. Remove the O-ring from the suction hose sub-assembly.
      NOTE:

      Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  15. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 
    1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose.
      GTY839022Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.

    2. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
      NOTE:

      Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  16. REMOVE COMPRESSOR WITH MOTOR ASSEMBLY 
    1. Disconnect the connector (A).
      GTY927569Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Connector (A)
    2. Remove the 2 nuts.
      GTY839024Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using an E8 "TORX" socket wrench, remove the 2 stud bolts and bolt.
      NOTE:

      Do not drop or subject the parts to any impact.

      GTY856134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt
      Stud Bolt
    4. Slide the green-colored lock of the connector (B) as shown in the illustration to release it and disconnect the connector.
      GTY934576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Connector (B)
      Slide
      Green-colored Lock
      WARNING:

      Make sure to wear insulated gloves.

      NOTE:

      Insulate the disconnected terminals and connector with insulating tape.

    5. Remove the compressor with motor assembly from the location shown in the illustration.
      GTY838989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage surrounding parts.

scientia non olet · About LEMON Manuals