LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 XLE, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 62 (Heating / Air Conditioning System (HV) - Diagnostic Codes (1 Of 3)) >> AIR CONDITIONING SYSTEM (for HV Model) >> DTC B1443: Air Outlet Damper Control Servo Motor Circuit [02/2019 - 08/2020] >> Procedure

DTC B1443: Air Outlet Damper Control Servo Motor Circuit [02/2019 - 08/2020]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK VEHICLE TYPE 

    Result

    Result  Proceed to 
    w/ Driver Seat Centralized Control A
    w/o Driver Seat Centralized Control B

    Result: 

    B 

    See step  11

    Result: 

    A 

    See step  2

  2. CHECK FOR DTC 
    1. Check for DTCs.

      Refer to DTC CHECK / CLEAR [11/2018 - ]

      Body Electrical > Air Conditioner > Trouble Codes 

      Result

      Result Proceed to
      DTC B1443 is output A
      DTC B1443 and B1497 are output B

    Result: 

    B 

    GO TO DTC B1497 

    Refer to DTC B1497: Communication Malfunction (Bus Ic) [11/2018 - 08/2020]

    Result: 

    A 

    See step  3

  3. CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 
    1. Check that the No. 3 air conditioning radiator damper servo sub-assembly is installed correctly.

      OK

      No. 3 air conditioning radiator damper servo sub-assembly is installed correctly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REINSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 

    Refer to REASSEMBLY [11/2018 - 08/2020]

    Result: 

    OK 

    See step  4

  4. CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER) 
    1. Check for a wire harness caught between the links of the motors and dampers.

      OK

      No wire harnesses are caught between the links of the motors and dampers.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REMOVE PINCHED WIRE HARNESS 

    Result: 

    OK 

    See step  5

  5. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Outlet Servo Pulse (D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) pulse Min.: 128
      Max.: 383      		 Operates between 164 to 278 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Actu Pulse(D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) actual pulse Min.: 128
      Max.: 383
      • S-FLOW: 278 (pulse)
      • FACE: 256 (pulse)
      • B/L: 245 (pulse)
      • FOOT-A: 224 (pulse)
      • FOOT-R (F): 215 (pulse)
      • FOOT-D: 207 (pulse)
      • F/D-R: 192 (pulse)
      • D/F: 173 (pulse)
      • DEF: 164 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Outlet Servo Pulse (D)
      Data List Display
      Air Outlet Servo Actu Pulse(D)

      OK

      The value of the Data List changes in accordance with the operation of the Active Test.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  6

  6. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Outlet Servo Pulse (D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) pulse Min.: 128
      Max.: 383      		 Operates between 164 to 278 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Pulse (D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) target pulse Min.: 128
      Max.: 383
      • S-FLOW: 278 (pulse)
      • FACE: 256 (pulse)
      • B/L: 245 (pulse)
      • FOOT-A: 224 (pulse)
      • FOOT-R (F): 215 (pulse)
      • FOOT-D: 207 (pulse)
      • F/D-R: 192 (pulse)
      • D/F: 173 (pulse)
      • DEF: 164 (pulse)
      		 -
      Air Outlet Servo Actu Pulse(D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) actual pulse Min.: 128
      Max.: 383
      • S-FLOW: 278 (pulse)
      • FACE: 256 (pulse)
      • B/L: 245 (pulse)
      • FOOT-A: 224 (pulse)
      • FOOT-R (F): 215 (pulse)
      • FOOT-D: 207 (pulse)
      • F/D-R: 192 (pulse)
      • D/F: 173 (pulse)
      • DEF: 164 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Outlet Servo Pulse (D)
      Data List Display
      Air Outlet Servo Pulse (D)
      Air Outlet Servo Actu Pulse(D)

      OK

      The target pulse value of the Data List matches the actual pulse.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

    Result: 

    NG 

    See step  7

  7. REPLACE NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 

    HINT: 

    Refer to DISASSEMBLY [11/2018 - 08/2020]

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  8

  8. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Outlet Servo Pulse (D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) pulse Min.: 128
      Max.: 383      		 Operates between 164 to 278 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Actu Pulse(D) No. 3 air conditioning radiator damper servo sub-assembly (driver side mode) actual pulse Min.: 128
      Max.: 383
      • S-FLOW: 278 (pulse)
      • FACE: 256 (pulse)
      • B/L: 245 (pulse)
      • FOOT-A: 224 (pulse)
      • FOOT-R (F): 215 (pulse)
      • FOOT-D: 207 (pulse)
      • F/D-R: 192 (pulse)
      • D/F: 173 (pulse)
      • DEF: 164 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Outlet Servo Pulse (D)
      Data List Display
      Air Outlet Servo Actu Pulse(D)

      OK

      The value of the Data List changes in accordance with the operation of the Active Test.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE AIR CONDITIONING HARNESS ASSEMBLY 

    Refer to DISASSEMBLY [11/2018 - 08/2020]

  9. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) pulse Min.: 128
      Max.: 383      		 Operates between 165 to 257 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Mix Servo Actual Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) actual pulse Min.: 128
      Max.: 383
      • MAX COLD: 257 (pulse)
      • MAX HOT: 165 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Mix Servo Targ Pulse(D)
      Data List Display
      Air Mix Servo Actual Pulse(D)

      OK

      The value of the Data List changes in accordance with the operation of the Active Test.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  7

    Result: 

    NG 

    See step  10

  10. CHECK AIR CONDITIONING RADIATOR ASSEMBLY (DAMPER) 
    1. Remove the No. 3 air conditioning radiator damper servo sub-assembly.

      Refer to DISASSEMBLY [11/2018 - 08/2020]

    2. Operate the dampers by hand.

      OK

      The dampers are easily operated by hand.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY 

    Refer to REMOVAL [11/2018 - ]

    Result: 

    NG 

    REPLACE AIR CONDITIONING RADIATOR ASSEMBLY 

  11. CHECK FOR DTC 
    1. Check for DTCs.

      Refer to DTC CHECK / CLEAR [02/2019 - ]

      Body Electrical > Air Conditioner > Trouble Codes 

      Result

      Result Proceed to
      DTC B1443 is output A
      DTC B1441, B1442, B1443 and B1446 are output B

    Result: 

    B 

    REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 

    Refer to DISASSEMBLY [02/2019 - 08/2020]

    Result: 

    A 

    See step  12

  12. CHECK FOR DTC 
    1. Check for DTCs.

      Refer to DTC CHECK / CLEAR [02/2019 - ]

      Body Electrical > Air Conditioner > Trouble Codes 

      Result

      Result Proceed to
      DTC B1443 is output A
      DTC B1443 and B1497 are output B

    Result: 

    B 

    GO TO DTC B1497 

    Refer to DTC B1497: Communication Malfunction (Bus Ic) [02/2019 - 08/2020]

    Result: 

    A 

    See step  13

  13. CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 
    1. Check that the No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.

      OK

      No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REINSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 

    Refer to REASSEMBLY [02/2019 - 08/2020]

    Result: 

    OK 

    See step  14

  14. CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER) 
    1. Check for a wire harness caught between the links of the motors and dampers.

      OK

      No wire harnesses are caught between the links of the motors and dampers.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REMOVE PINCHED WIRE HARNESS 

    Result: 

    OK 

    See step  15

  15. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) pulse Min.: 128
      Max.: 383      		 Operates between 234 to 348 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Actu Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) actual pulse Min.: 128
      Max.: 383
      • S-FLOW: 234 (pulse)
      • FACE: 256 (pulse)
      • B/L: 267 (pulse)
      • FOOT-A: 288 (pulse)
      • FOOT-R (F): 297 (pulse)
      • FOOT-D: 305 (pulse)
      • F/D-R: 320 (pulse)
      • D/F: 339 (pulse)
      • DEF: 348 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Outlet Servo Pulse (D)
      Data List Display
      Air Outlet Servo Actu Pulse(D)

      OK

      The value of the Data List changes in accordance with the operation of the Active Test.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  19

    Result: 

    OK 

    See step  16

  16. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) pulse Min.: 128
      Max.: 383      		 Operates between 234 to 348 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) target pulse Min.: 128
      Max.: 383
      • S-FLOW: 234 (pulse)
      • FACE: 256 (pulse)
      • B/L: 267 (pulse)
      • FOOT-A: 288 (pulse)
      • FOOT-R (F): 297 (pulse)
      • FOOT-D: 305 (pulse)
      • F/D-R: 320 (pulse)
      • D/F: 339 (pulse)
      • DEF: 348 (pulse)
      		 -
      Air Outlet Servo Actu Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) actual pulse Min.: 128
      Max.: 383
      • S-FLOW: 234 (pulse)
      • FACE: 256 (pulse)
      • B/L: 267 (pulse)
      • FOOT-A: 288 (pulse)
      • FOOT-R (F): 297 (pulse)
      • FOOT-D: 305 (pulse)
      • F/D-R: 320 (pulse)
      • D/F: 339 (pulse)
      • DEF: 348 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Outlet Servo Pulse (D)
      Data List Display
      Air Outlet Servo Pulse (D)
      Air Outlet Servo Actu Pulse(D)

      OK

      The target pulse value of the Data List matches the actual pulse.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

    Result: 

    NG 

    See step  17

  17. REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY 

    HINT: 

    Refer to DISASSEMBLY [02/2019 - 08/2020]

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  18

  18. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) pulse Min.: 128
      Max.: 383      		 Operates between 234 to 348 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Actu Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (front mode) actual pulse Min.: 128
      Max.: 383
      • S-FLOW: 234 (pulse)
      • FACE: 256 (pulse)
      • B/L: 267 (pulse)
      • FOOT-A: 288 (pulse)
      • FOOT-R (F): 297 (pulse)
      • FOOT-D: 305 (pulse)
      • F/D-R: 320 (pulse)
      • D/F: 339 (pulse)
      • DEF: 348 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Outlet Servo Pulse (D)
      Data List Display
      Air Outlet Servo Actu Pulse(D)

      OK

      The value of the Data List changes in accordance with the operation of the Active Test.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE AIR CONDITIONING HARNESS ASSEMBLY 

    Refer to DISASSEMBLY [02/2019 - 08/2020]

  19. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Using the Techstream, perform the following Active Test and read the Data List value.

      Body Electrical > Air Conditioner > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) pulse Min.: 128
      Max.: 383      		 Operates between 165 to 257 pulses

      Body Electrical > Air Conditioner > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Mix Servo Actual Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) actual pulse Min.: 128
      Max.: 383
      • MAX COLD: 257 (pulse)
      • MAX HOT: 165 (pulse)
      		 -

      Body Electrical > Air Conditioner > Active Test 

      Active Test Display
      Air Mix Servo Targ Pulse(D)
      Data List Display
      Air Mix Servo Actual Pulse(D)

      OK

      The value of the Data List changes in accordance with the operation of the Active Test.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  17

    Result: 

    NG 

    See step  20

  20. CHECK AIR CONDITIONING RADIATOR ASSEMBLY (DAMPER) 
    1. Remove the No. 1 air conditioning radiator damper servo sub-assembly.

      Refer to DISASSEMBLY [02/2019 - 08/2020]

    2. Operate the dampers by hand.

      OK

      The dampers are easily operated by hand.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY 

    Refer to REMOVAL [11/2018 - ]

    Result: 

    NG 

    REPLACE AIR CONDITIONING RADIATOR ASSEMBLY 

scientia non olet · About LEMON Manuals