LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 XLE, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 19 (Hybrid Transaxle System (P710) - Service Information (2 Of 2)) >> Shift Lever Position Sensor >> Removal [11/2018 - ] >> Procedure

Removal [11/2018 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. SECURE VEHICLE 
    1. Fully apply the parking brake and chock a wheel.
      WARNING:
      • Make sure to apply the parking brake and chock a wheel before performing this procedure.
      • If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
      GTY655852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 13 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 13 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 13 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 13 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 13 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 13 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 13 [10/2023 - ]

  3. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 14 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 14 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 14 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 14 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 14 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 14 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 14 [10/2023 - ]

  4. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 15 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 15 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 15 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 15 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 15 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 15 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 15 [10/2023 - ]

  5. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 16 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 16 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 16 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 16 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 16 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 16 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 16 [10/2023 - ]

  6. REMOVE INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 3 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 3 [02/2019 - 08/2020] , or refer to PROCEDURE - Step 3 [08/2020 - ]

  7. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 26 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 26 [02/2019 - 10/2019] , or refer to PROCEDURE - Step 26 [10/2019 - 08/2020] , or refer to PROCEDURE - Step 26 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 26 [12/2021 - 10/2022] , or refer to PROCEDURE - Step 26 [10/2022 - 10/2023] , or refer to PROCEDURE - Step 26 [10/2023 - ]

  8. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 4 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 4 [02/2019 - 08/2020] , or refer to PROCEDURE - Step 4 [08/2020 - ]

  9. DISCONNECT MOTOR COOLING COOLER 
    1. Remove the 3 bolts to disconnect the motor cooling cooler from the No. 1 transmission control cable bracket.
      GTY869289Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Move the shift lever to N.
    2. Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever.
      GTY929604Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with the clip from the No. 1 transmission control cable bracket.
      GTY853681Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using a screwdriver, disengage the 2 claws and remove the clip from the transmission control cable assembly.
      GTY745662Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE SHIFT LEVER POSITION SENSOR 
    1. Disconnect the shift lever position sensor connector.
      GTY853678Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the nut, washer and transmission control shaft lever from the shift lever position sensor.
      GTY853682Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a screwdriver with its tip wrapped with protective tape, pry out the tabs of the lock plate.
      GTY889157Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Lock Plate
      *a Protective Tape
    4. Remove the lock nut and lock plate from the shift lever position sensor.
      GTY889609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Lock Nut
      *2 Lock Plate
    5. Remove the 2 bolts and shift lever position sensor from the hybrid vehicle transaxle assembly.
      GTY853683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals