LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 XLE, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 150 (Hybrid Transaxle System / Rear Traction Motor (Q610) - Service Information) >> Hybrid Transaxle Side Gear Oil Seal >> Replacement [10/2019 - 08/2020] >> Procedure

Replacement [10/2019 - 08/2020]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. REMOVE NO. 1 FLOOR UNDER COVER (w/ No. 1 Floor Under Cover) 

    Refer to PROCEDURE - Step 1 [02/2019 - 06/2020] , or refer to PROCEDURE - Step 1 [06/2020 - 08/2020]

  2. DRAIN HYBRID TRANSAXLE FLUID 

    See step  2

  3. REMOVE REAR DRIVE SHAFT ASSEMBLY 

    Refer to REMOVAL [02/2019 - 12/2021]

  4. REMOVE REAR DRIVE SHAFT OIL SEAL LH 
    1. Using SST, remove the rear drive shaft oil seal LH from the rear traction motor with transaxle assembly.
      • SST: 09308-00010 
      NOTE:

      Be careful not to damage the rear traction motor with transaxle assembly.

      GTY858521Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE REAR DRIVE SHAFT OIL SEAL RH 
    1. Using SST, remove the rear drive shaft oil seal RH from the rear traction motor with transaxle assembly.
      • SST: 09612-65014 
        1. 09612-01020
      NOTE:

      Be careful not to damage the rear traction motor with transaxle assembly.

      GTY881856Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Hold
      Turn
  6. INSTALL REAR DRIVE SHAFT OIL SEAL RH 
    1. Apply MP grease to the lip of a new rear drive shaft oil seal RH.
    2. Using SST and a hammer, install the rear drive shaft oil seal RH to the rear traction motor with transaxle assembly.
      • SST: 09316-20011 
      • SST: 09517-30010 

      Standard Depth

      -0.5 to 0.5 mm (-0.0196 to 0.0196 in.)

      GTY870663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Depth
      *b Inner Lip
      *c Outer Lip
      NOTE:
      GTY745251Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Correct
      *b Incorrect
      *c Outer Lip
      • Make sure that the outer lip of the rear drive shaft oil seal RH is not pinched by SST.
      • Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal RH.
      • Do not install the rear drive shaft oil seal RH at an angle.
      • Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal RH.
  7. INSTALL REAR DRIVE SHAFT OIL SEAL LH 
    1. Apply MP grease to the lip of a new rear drive shaft oil seal LH.
    2. Using SST and a hammer, install the rear drive shaft oil seal LH to the rear traction motor with transaxle assembly.
      • SST: 09316-20011 
      • SST: 09517-30010 

      Standard Depth

      -0.5 to 0.5 mm (-0.0196 to 0.0196 in.)

      GTY870252Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Depth
      *b Inner Lip
      *c Outer Lip
      NOTE:
      GTY745251Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Correct
      *b Incorrect
      *c Outer Lip
      • Make sure that the outer lip of the rear drive shaft oil seal LH is not pinched by SST.
      • Do not allow foreign matter to attach to the inner lip and outer lip of the rear drive shaft oil seal LH.
      • Do not install the rear drive shaft oil seal LH seal at an angle.
      • Do not remove the grease from the inner lip and outer lip of the rear drive shaft oil seal LH.
  8. INSTALL REAR DRIVE SHAFT ASSEMBLY 

    Refer to INSTALLATION [10/2019 - ]

  9. ADD HYBRID TRANSAXLE FLUID 

    See step  3

  10. INSPECT HYBRID TRANSAXLE FLUID 

    See step  3

  11. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK 
  12. INSTALL NO. 1 FLOOR UNDER COVER (w/ No. 1 Floor Under Cover) 

    Refer to PROCEDURE - Step 36 [02/2019 - 06/2020] , or refer to PROCEDURE - Step 36 [06/2020 - 12/2021]

scientia non olet · About LEMON Manuals