Data List / Active Test [02/2019 - 10/2022]
- DATA LIST NOTE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Immobiliser / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Key SW Unlock warning switch signal ON or OFF ON: Door control transmitter assembly in ignition key cylinder
OFF: No door control transmitter assembly in ignition key cylinder- IG SW Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch ACC or off"OFF" is also displayed for this item when the ignition switch is ACC. Immobiliser Immobiliser system status Set or Unset Set: No door control transmitter assembly in ignition key cylinder, or 20 seconds elapsed after turning the ignition switch to ACC or off
Unset: Door control transmitter assembly in ignition key cylinder- Response Transponder chip data NG or OK NG: Data error
OK: Data OK- Frame Error Transponder chip data NG or OK NG: Data error
OK: Data OK- Different Serial Number Transponder chip data NG or OK NG: Data error
OK: Data OK- Different Encrypt Code Transponder chip data NG or OK NG: Data error
OK: Data OK- Abnormal Status Transponder chip data NG or OK NG: Data error
OK: Data OK- Bcc Malfunction Transponder chip data NG or OK NG: Incorrect data being sent
OK: Correct data being sent- Sub Key Sub key ID code signal Reg or Unreg Reg: Registered sub key ID code sent
Unreg: Unmatching sub key ID code sent- Master Key Master key ID code signal Reg or Unreg Reg: Registered master key ID code sent
Unreg: Unmatching master key ID code sent- Transponder S-code Number of registered sub keys Min.: 0, Max.: 15 Number of registered sub keys displayed - Transponder M-code Number of registered master keys Min.: 0, Max.: 15 Number of registered master keys displayed - Reg Code Space Full Key registration code memory space full No or Yes No: Possible to register more key codes
Yes: Cannot register any more key codes- +B Power source Break or Normal Break: Power source open
Normal: Power source normal- Antenna Coil Status Transponder key coil condition Normal or Fail Normal: Antenna coil normal
Fail: Antenna coil malfunctioning- EEPROM Status EEPROM status NG or OK NG: Data error
OK: Data OK- E/G Start Permission Hybrid control system start permission NG or OK NG: Hybrid control system start not permitted
OK: Hybrid control system start permitted- The Number of DTCs Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs - HINT:
Data from an actual vehicle provided for reference.
- *1: Insert a door control transmitter assembly into the ignition key cylinder and turn the ignition switch to ACC.
- *2: Turn the ignition switch to ON.
- *3: Turn the ignition switch off and remove the door control transmitter assembly from the ignition key cylinder.
- Enter the following menus: Powertrain / Hybrid Control / Data List.
- Read the Data List according to the display on the Techstream.
Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Permit Start by Immobiliser Status of the permit start by "Immobiliser System" No Judgment, OK or NG No Judgment: No judgment
OK: Hybrid control system start permitted
NG: Hybrid control system start not permitted-
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Main Body* or Immobiliser / Active Test.
- *: w/ Theft Deterrent System
- Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Security Indicator Combination meter assembly (security indicator light) OFF/ON w/ Theft Deterrent System Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Security Indicator Combination meter assembly (security indicator light) OFF/ON -