LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 XLE, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 122 (Fuel System (A25A-FXS) - Inspection) >> Fuel System >> On-Vehicle Inspection [02/2019 - ] >> Procedure

On-Vehicle Inspection [02/2019 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK 
    1. Check fuel pump operation.
      1. Connect the Techstream to the DLC3.
      2. Turn the power switch on (IG).
        NOTE:

        Do not start the engine.

      3. Turn the Techstream on.
      4. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

        Powertrain > Engine > Active Test 

        Tester Display
        Activate the Circuit Relay
      5. Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.
    2. Inspect for fuel leaks.
      1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
    3. Turn the power switch off.
    4. Disconnect the Techstream from the DLC3.
  2. CHECK FUEL PRESSURE 
    1. Discharge fuel system pressure.

      Refer to PRECAUTION [02/2019 - 08/2020] , or refer to PRECAUTION [08/2020 - ] 

    2. Measure the auxiliary battery voltage.

      Standard voltage

      11 to 14 V

    3. Disconnect the cable from the negative (-) auxiliary battery terminal.
      NOTE:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Refer to INITIALIZATION [02/2019 - 10/2019] , or refer to INITIALIZATION [10/2019 - 06/2020] , or refer to INITIALIZATION [06/2020 - 08/2020] , or refer to INITIALIZATION [08/2020 - 12/2021] , or refer to INITIALIZATION [12/2021 - 10/2022] , or refer to INITIALIZATION [10/2022 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

    4. Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.
      GTY745455Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Open
      Pull
    5. Disconnect the fuel tube sub-assembly from the fuel pipe.
      GTY760017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to PRECAUTION [02/2019 - 08/2020] , or refer to PRECAUTION [08/2020 - ] 

    6. Install SST (EFI fuel pressure gauge) as shown in the illustration.
      GTY713748Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Fuel Tube Sub-assembly (Vehicle Side)
      *a SST (Hose Band)
      *b SST (T-joint)
      *c SST (Gauge)
      *d SST (Hose Joint)
      *e SST (Hose)
      *f SST (Fuel Tube Connector)
      *g Fuel Pipe (Vehicle Side)
      • SST: 09268-45101 
        1. 09268-41250
        2. 09268-41260
        3. 09268-41280
        4. 09268-41500
        5. 09268-41700
        6. 95336-08070
    7. Wipe up any spilled fuel.
    8. Connect the cable to the negative (-) auxiliary battery terminal.
      NOTE:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Refer to INITIALIZATION [02/2019 - 10/2019] , or refer to INITIALIZATION [10/2019 - 06/2020] , or refer to INITIALIZATION [06/2020 - 08/2020] , or refer to INITIALIZATION [08/2020 - 12/2021] , or refer to INITIALIZATION [12/2021 - 10/2022] , or refer to INITIALIZATION [10/2022 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

    9. Connect the Techstream to the DLC3.
    10. Turn the power switch on (IG).
      NOTE:

      Do not start the engine.

    11. Turn the Techstream on.
    12. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

      Powertrain > Engine > Active Test 

      Tester Display
      Activate the Circuit Relay
    13. Measure the fuel pressure.

      Standard fuel pressure

      294 to 833 kPa (3.0 to 8.5 kgf/cm2 , 43 to 121 psi)

      • If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump, fuel filter and fuel main valve assembly.
      • If the result is not as specified, replace the fuel main valve assembly.
    14. Put the engine in Inspection Mode (Maintenance Mode).

      Powertrain > Hybrid Control > Utility 

      Tester Display
      Inspection Mode
    15. Start the engine.
    16. Measure the fuel pressure at idle.

      Standard fuel pressure

      294 to 833 kPa (3.0 to 8.5 kgf/cm2 , 43 to 121 psi)

      HINT: 

      Refer to Standard Idle Speed.

      Refer to PROCEDURE - Step 8 [02/2019 - 08/2020] , or refer to PROCEDURE - Step 8 [08/2020 - ]

    17. Stop the engine.
    18. Check that the fuel pressure remains as specified for 5 minutes.

      Standard fuel pressure

      98 kPa (1.0 kgf/cm2 , 14.2 psi) or more

      If the result is not as specified, check the fuel pump, fuel main valve assembly and/or port fuel injector assemblies.

    19. After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent fuel from spraying.
      NOTE:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Refer to INITIALIZATION [02/2019 - 10/2019] , or refer to INITIALIZATION [10/2019 - 06/2020] , or refer to INITIALIZATION [06/2020 - 08/2020] , or refer to INITIALIZATION [08/2020 - 12/2021] , or refer to INITIALIZATION [12/2021 - 10/2022] , or refer to INITIALIZATION [10/2022 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

    20. Connect the fuel tube sub-assembly to the fuel pipe.

      Refer to PRECAUTION [02/2019 - 08/2020] , or refer to PRECAUTION [08/2020 - ] 

    21. Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.
    22. Inspect for fuel leaks.

      See step  1

  3. CHECK FUEL PRESSURE (for High Pressure) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Put the engine in Inspection Mode (Maintenance Mode).

      Powertrain > Hybrid Control > Utility 

      Tester Display
      Inspection Mode
    5. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.
    6. Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Coolant Temperature, Fuel Pressure (High) and Injection Mode.

      Powertrain > Engine > Data List 

      Tester Display
      Engine Speed
      Coolant Temperature
      Fuel Pressure (High)
      Injection Mode
    7. According to the display on the Techstream, read the Data List.

      HINT: 

      During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.

      Standard

      Techstream Display Condition Specified Condition
      Fuel Pressure (High)
      • Shift position: P
      • A/C: Off
      • Engine warmed up
      • Engine Speed: 2500 rpm
      • Injection Mode: Direct
      		 3000 to 25000 kPag

      If the result is not as specified, check the fuel pump, fuel pump assembly, fuel pressure sensor and wire harnesses.

    8. Stop the engine.
scientia non olet · About LEMON Manuals