LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 LE, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 147 (Hybrid Battery System (Lithium-Ion Battery) - Diagnostic Codes (2 Of 3)) >> HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) >> DTC P0B13-62: Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure [06/2020 - ] >> Procedure

DTC P0B13-62: Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure [06/2020 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.
    4. Check for DTCs.

      Powertrain > HV Battery > Trouble Codes 

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result Proceed to
      "P0B13-62" only is output, or DTCs except the ones in the table below are also output. A
      DTCs of hybrid battery system in the table below are output. B
      DTCs of hybrid control system in the table below are output. C
      System Relevant DTC
      Hybrid battery system P060A-47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
      P060B-49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
      P0606-87 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
      Hybrid control system P0A1F-94 Hybrid/EV Battery Energy Control Module Unexpected Operation
    5. Turn the ignition switch off.

    Result: 

    B 

    GO TO DTC CHART (HYBRID BATTERY SYSTEM) 

    Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2020 - ]

    Result: 

    C 

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) 

    Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2020 - 12/2021] , or refer to DIAGNOSTIC TROUBLE CODE CHART [12/2021 - 11/2024] , or refer to DIAGNOSTIC TROUBLE CODE CHART [11/2024 - ]

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY) 

    Refer to PROCEDURE - Step 10

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY) 

    Refer to PROCEDURE - Step 9

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY) 

    See step  4

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    See step  8

    Result: 

    OK 

    See step  5

  5. REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  6

  6. CLEAR DTC (HV BATTERY) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Enter the following menus: Powertrain / HV Battery / Clear DTCs.
    4. Clear the DTCs and freeze frame data.

      Powertrain > HV Battery > Clear DTCs 

    5. Perform a road test.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  7

  7. CHECK DTC OUTPUT (HV BATTERY) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Enter the following menus: Powertrain / HV Battery / Trouble Codes.
    4. Check for DTCs.

      Powertrain > HV Battery > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output. A
      P0B13-62 is also output. B
    5. Turn the ignition switch off.

    Result: 

    A 

    END 

    Result: 

    B 

    REPLACE BATTERY ECU ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

  8. CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY) 

    See step  9

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

    Result: 

    NG 

    REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

  9. CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY) 

    Refer to PROCEDURE - Step 9

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

    Result: 

    NG 

    REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY AND NO. 2 HV SUPPLY STACK SUB-ASSEMBLY 

    Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

scientia non olet · About LEMON Manuals