DTC P3147-79: Transmission (Shaft) Mechanical Linkage Failure [06/2020 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.

CHECK DTC OUTPUT (ENGINE)

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine / Trouble Codes.

Check for DTCs.

Powertrain > Engine > Trouble Codes

Result

Result	Proceed to
No DTCs are output, or DTCs except the ones in the table below are also output.	A
Any of the following DTCs are also output.	B

Relevant DTC
P0335-11	Crankshaft Position Sensor "A" Circuit Short to Ground
P0335-15	Crankshaft Position Sensor "A" Circuit Short to Battery or Open
P0335-2A	Crankshaft Position Sensor "A" Signal Stuck in Range
P0335-31	Crankshaft Position Sensor "A" No Signal

Turn the ignition switch off.

Result:

B

GO TO DTC CHART (SFI SYSTEM)

Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2020 - 08/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2020 - 12/2021] , or refer to DIAGNOSTIC TROUBLE CODE CHART [12/2021 - 10/2022] , or refer to DIAGNOSTIC TROUBLE CODE CHART [10/2022 - 11/2024] , or refer to DIAGNOSTIC TROUBLE CODE CHART [11/2024 - ]

Result:

A

See step 2

CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)
Refer to PROCEDURE - Step 1

Result

Proceed to

OK

NG

Result:

NG

See step 7

Result:

OK

See step 3
CLEAR DTC
Refer to PROCEDURE - Step 2

Result

Proceed to

NEXT

Result:

NEXT

See step 4
CHECK ENGINE RACING
Refer to PROCEDURE - Step 3

Result

Proceed to

OK

NG

Result:

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result:

OK

See step 5
CHECK CREEP MOVEMENT
Refer to PROCEDURE - Step 4

Result

Proceed to

OK

NG

Result:

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result:

OK

See step 6

INSPECT ENGINE SPEED

Refer to PROCEDURE - Step 5

Result

Result	Proceed to
The absolute value of the difference is less than 500 rpm.	A
The absolute value of the difference is 500 rpm or more continuously for 1 second.	B

Result:

A

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result:

B

REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY

Refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
Refer to PROCEDURE - Step 6

Result

Proceed to

OK

NG

Result:

OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Refer to REMOVAL [06/2020 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result:

NG

REPAIR OR REPLACE ENGINE