LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> RAV4 LE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 22 (Seat Belt Warning System - Diagnostics & Symptom Tests) >> Seat Belt Warning System >> Rear Seat Belt Warning Light Malfunction [10/2023 - 11/2024] >> Procedure

Rear Seat Belt Warning Light Malfunction [10/2023 - 11/2024]: Procedure

WARNING: This page is about a different car, the 2025 Toyota RAV4, 2024 Toyota RAV4, 2023 Toyota RAV4, 2022 Toyota RAV4, and 2021 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK VEHICLE TYPE 
    1. Check Vehicle Type.

      Result

      Result Proceed to
      for Type A A
      for Type B B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RR Door Courtesy Switch Status Rear door courtesy light switch RH signal Close or Open Close: Rear door RH closed
      Open: Rear door RH open      		 -
      RL Door Courtesy Switch Status Rear door courtesy light switch LH signal Close or Open Close: Rear door LH closed
      Open: Rear door LH open      		 -

      Body Electrical > Main Body > Data List 

      Tester Display
      RR Door Courtesy Switch Status
      RL Door Courtesy Switch Status

      OK

      The Techstream display changes correctly in response to the rear door condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    GO TO LIGHTING SYSTEM 

    Refer to Door Courtesy Switch Circuit [10/2023 - 11/2024]

    Result: 

    OK 

    See step  3

  3. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Rear Right Seat Buckle / Occupant Detection Warning Switch Rear seat inner belt buckle signal ON or OFF OFF: Rear RH seat belt fastened
      ON: Rear RH seat belt not fastened      		 -
      Rear Left Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for LH) buckle signal ON or OFF OFF: Rear LH seat belt (for LH) fastened
      ON: Rear LH seat belt (for LH) not fastened      		 -
      Rear Center Seat Buckle / Occupant Detection Warning Switch Rear seat inner with center belt LH (for Center) buckle signal ON or OFF OFF: Rear LH seat belt (for Center) fastened
      ON: Rear LH seat belt (for Center) not fastened      		 -

      Body Electrical > Combination Meter > Data List 

      Tester Display
      Rear Right Seat Buckle / Occupant Detection Warning Switch
      Rear Left Seat Buckle / Occupant Detection Warning Switch
      Rear Center Seat Buckle / Occupant Detection Warning Switch

      Result

      Result Proceed to
      All item is normal A
      "Rear Right Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear seat belt condition B
      "Rear Left Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear LH seat belt condition C
      "Rear Center Seat Buckle / Occupant Detection Warning Switch" item does not switch to "ON" or "OFF" according to the rear center seat belt condition D

    Result: 

    A 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [10/2022 - ]

    Result: 

    C 

    See step  7

    Result: 

    D 

    See step  9

    Result: 

    B 

    See step  4

  4. INSPECT REAR SEAT INNER BELT ASSEMBLY 
    1. Remove the rear seat inner belt assembly.

      Refer to REMOVAL [11/2018 - ]

    2. Inspect the rear seat inner belt assembly.

      Refer to INSPECTION [11/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SEAT INNER BELT ASSEMBLY 

    Refer to REMOVAL [11/2018 - ]

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the N37 rear seat inner belt assembly connector.
    2. Disconnect the G19*1 or G141*2 combination meter assembly connector.
      1. *1: for 7 Inch Multi-information Display Type
      2. *2: for 12.3 Inch Multi-information Display Type
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      FOR 7 INCH MULTI-INFORMATION DISPLAY TYPE

      Tester Connection Condition Specified Condition
      N37-5 (RBR+) - G19-35 (RRSB) Always Below 1 Ω
      N37-5 (RBR+) or G19-35 (RRSB) - Body ground Always 10 kΩ or higher
      N37-4 (RBR-) - Body ground Always Below 1 Ω
      FOR 12.3 INCH MULTI-INFORMATION DISPLAY TYPE

      Tester Connection Condition Specified Condition
      N37-5 (RBR+) - G141-30 (RRSB) Always Below 1 Ω
      N37-5 (RBR+) or G141-30 (RRSB) - Body ground Always 10 kΩ or higher
      N37-4 (RBR-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [10/2022 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RR Door Courtesy SW Rear door courtesy light switch RH signal OFF or ON OFF: Rear door RH closed
      ON: Rear door RH open      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH signal OFF or ON OFF: Rear door LH closed
      ON: Rear door LH open      		 -

      Body Electrical > Main Body > Data List 

      Tester Display
      RR Door Courtesy SW
      RL Door Courtesy SW

      OK

      The Techstream display changes correctly in response to the rear door condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  3

    Result: 

    NG 

    GO TO LIGHTING SYSTEM 

    Refer to Door Courtesy Switch Circuit [10/2023 - 11/2024]

  7. INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH 
    1. Remove the rear seat inner with center belt assembly LH.

      Refer to REMOVAL [11/2018 - ]

    2. Inspect the rear seat inner with center belt assembly LH.

      Refer to INSPECTION [11/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH 

    Refer to REMOVAL [11/2018 - ]

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the N38 rear seat inner with center belt assembly LH connector.
    2. Disconnect the G19*1 or G141*2 combination meter assembly connector.
      1. *1: for 7 Inch Multi-information Display Type
      2. *2: for 12.3 Inch Multi-information Display Type
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      FOR 7 INCH MULTI-INFORMATION DISPLAY TYPE

      Tester Connection Condition Specified Condition
      N38-5 (LBR+) - G19-36 (RLSB) Always Below 1 Ω
      N38-5 (LBR+) or G19-36 (RLSB) - Body ground Always 10 kΩ or higher
      N38-4 (LBR-) - Body ground Always Below 1 Ω
      FOR 12.3 INCH MULTI-INFORMATION DISPLAY TYPE

      Tester Connection Condition Specified Condition
      N38-5 (LBR+) - G141-21 (RLSB) Always Below 1 Ω
      N38-5 (LBR+) or G141-21 (RLSB) - Body ground Always 10 kΩ or higher
      N38-4 (LBR-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [10/2022 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  9. INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH 
    1. Remove the rear seat inner with center belt assembly LH.

      Refer to REMOVAL [11/2018 - ]

    2. Inspect the rear seat inner with center belt assembly LH.

      Refer to INSPECTION [11/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH 

    Refer to REMOVAL [11/2018 - ]

    Result: 

    OK 

    See step  10

  10. CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the N39 rear seat inner with center belt assembly LH connector.
    2. Disconnect the G19*1 or G141*2 combination meter assembly connector.
      1. *1: for 7 Inch Multi-information Display Type
      2. *2: for 12.3 Inch Multi-information Display Type
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      FOR 7 INCH MULTI-INFORMATION DISPLAY TYPE

      Tester Connection Condition Specified Condition
      N39-4 (CBR+) - G19-19 (RCSB) Always Below 1 Ω
      N39-4 (CBR+) or G19-19 (RCSB) - Body ground Always 10 kΩ or higher
      N39-3 (CBR-) - Body ground Always Below 1 Ω
      FOR 12.3 INCH MULTI-INFORMATION DISPLAY TYPE

      Tester Connection Condition Specified Condition
      N39-4 (CBR+) - G141-22 (RCSB) Always Below 1 Ω
      N39-4 (CBR+) or G141-22 (RCSB) - Body ground Always 10 kΩ or higher
      N39-3 (CBR-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [10/2022 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals