How To Proceed With Troubleshooting [08/2020 - ]: Procedure

Result

Result: 

NEXT 

See step  2

1. Interview the customer to confirm the problem.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Measure the auxiliary battery voltage.

   Standard voltage

   11 to 14 V

   If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

2. Check the fuses and relays.
3. Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Using the Techstream, check for CAN communication system DTCs.

   for Gasoline Model: Refer to DIAGNOSIS SYSTEM [08/2020 - 12/2021] , or refer to DIAGNOSIS SYSTEM [12/2021 - 10/2022] , or refer to DIAGNOSIS SYSTEM [10/2022 - 10/2023] , or refer to DIAGNOSIS SYSTEM [10/2023 - 11/2024] , or refer to DIAGNOSIS SYSTEM [11/2024 - ]

   for HV Model: Refer to DIAGNOSIS SYSTEM [08/2020 - 12/2021] , or refer to DIAGNOSIS SYSTEM [12/2021 - 10/2022] , or refer to DIAGNOSIS SYSTEM [10/2022 - 10/2023] , or refer to DIAGNOSIS SYSTEM [10/2023 - 11/2024] , or refer to DIAGNOSIS SYSTEM [11/2024 - ]

   Result

   Result	Proceed to
   CAN DTCs are not output	A
   CAN DTCs are output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM 

for Gasoline Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

for HV Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [02/2019 - ]

Result: 

A 

See step  5

1. Clear DTCs.

   Refer to DTC CHECK / CLEAR [08/2020 - ]

   Body Electrical > SRS Airbag > Clear DTCs 

2. Check for DTCs.

   Refer to DTC CHECK / CLEAR [08/2020 - ]

   Body Electrical > SRS Airbag > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO AIRBAG SYSTEM 

Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2020 - ]

Result: 

A 

See step  6

1. Check the operation of the speedometer and shift indicator on the combination meter assembly.

   OK

   The speedometer and shift indicator on the combination meter assembly operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO METER / GAUGE SYSTEM 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

Result: 

OK 

See step  7

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [08/2020 - ] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table	A
   Fault is listed in Problem Symptoms Table	B

Result: 

B 

See step  9

Result: 

A 

See step  8

1. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [08/2020 - 10/2023] , or refer to DATA LIST / ACTIVE TEST [10/2023 - 11/2024] , or refer to DATA LIST / ACTIVE TEST [11/2024 - ] 

2. Terminals of ECU

   Refer to TERMINALS OF ECU [08/2020 - 10/2022] , or refer to TERMINALS OF ECU [10/2022 - ] 

3. Operation check

   Refer to OPERATION CHECK [08/2020 - 10/2022] , or refer to OPERATION CHECK [10/2022 - ] 

4. Inspection

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

Result

Result: 

NEXT 

See step  10

Result

Result: 

NEXT 

END