Speedometer Malfunction [04/2018 - 08/2021]: Procedure
- CHECK CAN COMMUNICATION SYSTEM
- Check if CAN communication DTCs are output.
Refer to DIAGNOSIS SYSTEM [04/2018 - 08/2020] , or refer to DIAGNOSIS SYSTEM [08/2020 - 08/2021]
Result
Result Proceed to DTCs are not output A DTCs are output B
Result:
B
GO TO CAN COMMUNICATION SYSTEM. Refer to HOW TO PROCEED WITH TROUBLESHOOTING [04/2018 - ]
Result:
A
See step 2
- Check if CAN communication DTCs are output.
- CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
- Check if electronically controlled brake system DTCs are output.
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes
Result
Result Proceed to DTCs are not output A DTCs are output B
Result:
B
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM. Refer to DIAGNOSTIC TROUBLE CODE CHART [04/2018 - 08/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2020 - 08/2021]
Result:
A
See step 3
- Check if electronically controlled brake system DTCs are output.
- PERFORM ACTIVE TEST USING TECHSTREAM
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Combination Meter / Active Test.
- Perform the Active Test according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Speedometer Operation (0km/h, 0MPH) Speedometer (0 km/h, 0 mph) ON - Speedometer Operation (40km/h, 40MPH) Speedometer (40 km/h, 40 mph) ON The value displayed on the speedometer may deviate.
Reference mph*1:
40 → 39.4 to 42.2
Reference km/h*2:
40 → 38.7 to 43.2Speedometer Operation (80km/h, 80MPH) Speedometer (80 km/h, 80 mph) ON The value displayed on the speedometer may deviate.
Reference mph*1:
80 → 80.0 to 83.2
Reference km/h*2:
80 → 79.3 to 84.3Speedometer Operation (120km/h, 120M-PH) Speedometer (120 km/h, 120 mph) ON The value displayed on the speedometer may deviate.
Reference mph*1:
120 → 120.9 to 124.1
Reference km/h*2:
120 → 120.3 to 125.3Speedometer Operation (160km/h, 160M-PH) Speedometer (160 km/h, 160 mph)*2 ON The value displayed on the speedometer may deviate.
Reference km/h*2:
160 → 161.2 to 166.2Speedometer Operation (200km/h, 200M-PH) Speedometer (200 km/h, 200 mph)*2 ON The value displayed on the speedometer may deviate.
Reference km/h*2:
200 → 202.1 to 207.1Speedometer Operation (240km/h, 240M-PH) Speedometer (240 km/h, 240 mph)*2 ON The value displayed on the speedometer may deviate.
Reference km/h*2:
240 → 243.0 to 248.0- *1: for Speedometer with Imperial Units for Main Scale
- *2: for Speedometer with Metric Units for Main Scale
Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (0km/h, 0MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (40km/h, 40MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (80km/h, 80MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (120km/h, 120M-PH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (160km/h, 160M-PH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (200km/h, 200M-PH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (240km/h, 240M-PH) OK
Speedometer indication is normal.
Result
Proceed to OK NG
Result:
OK
REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY). Refer to REMOVAL [04/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021]
Result:
NG
REPLACE COMBINATION METER ASSEMBLY. Refer to REMOVAL [04/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021]