LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> Highlander L, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 47 (Engine Control System (T24A-FTS) - Circuit Tests (2 Of 2) & Symptom Tests) >> SFI System >> Ignition Circuit [10/2022 - ] >> Procedure

Ignition Circuit [10/2022 - ]: Procedure

WARNING: This page is about a different car, the 2025 Toyota Highlander, 2024 Toyota Highlander, and 2023 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY) 
    1. Disconnect the ignition coil assembly connectors.
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      C1-1 (+B) - C1-3 (GND) Ignition switch ON 11 to 14 V
      C2-1 (+B) - C2-3 (GND) Ignition switch ON 11 to 14 V
      C3-1 (+B) - C3-3 (GND) Ignition switch ON 11 to 14 V
      C4-1 (+B) - C4-3 (GND) Ignition switch ON 11 to 14 V
      GTY1250030Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Ignition Coil Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  3

    Result: 

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) 
    1. Disconnect the ignition coil assembly connectors.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C1-2 (IGT1) - C88-61 (IGT1) Always Below 1 Ω
      C2-2 (IGT2) - C88-60 (IGT2) Always Below 1 Ω
      C3-2 (IGT3) - C88-59 (IGT3) Always Below 1 Ω
      C4-2 (IGT4) - C88-58 (IGT4) Always Below 1 Ω
      C1-2 (IGT1) or C88-61 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
      C2-2 (IGT2) or C88-60 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
      C3-2 (IGT3) or C88-59 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
      C4-2 (IGT4) or C88-58 (IGT4) - Body ground and other terminals Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM 

    Refer to REMOVAL [10/2022 - 11/2023] , or refer to REMOVAL [11/2023 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  3. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND) 
    1. Disconnect the ignition coil assembly connectors.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C1-3 (GND) - Body ground Always Below 1 Ω
      C2-3 (GND) - Body ground Always Below 1 Ω
      C3-3 (GND) - Body ground Always Below 1 Ω
      C4-3 (GND) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT IGT/INJ RELAY 
    1. Inspect the IGT/INJ relay.

      Refer to PROCEDURE - Step 1 [10/2022 - 11/2023] , or refer to PROCEDURE - Step 1 [11/2023 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE IGT/INJ RELAY 

    Result: 

    OK 

    See step  5

  5. CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGT/INJ RELAY) 
    1. Remove the IGT/INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
    2. Measure the voltage according to the value(s) in the table below.
      GTY1250151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
      *2 IGT/INJ relay

      Standard Voltage

      Tester Connection Condition Specified Condition
      3 (IGT/INJ relay) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGT/INJ RELAY) 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - BODY GROUND) 
    1. Remove the IGT/INJ relay from the No. 1 engine room relay block and No. 1 junction block assembly.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (IGT/INJ relay) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - IGNITION COIL ASSEMBLY) 
    1. Disconnect the IGT/INJ relay from No. 1 engine room relay block and No. 1 junction block assembly.
    2. Disconnect the ignition coil assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      5 (IGT/INJ relay) - C1-1 (+B) Always Below 1 Ω
      5 (IGT/INJ relay) - C2-1 (+B) Always Below 1 Ω
      5 (IGT/INJ relay) - C3-1 (+B) Always Below 1 Ω
      5 (IGT/INJ relay) - C4-1 (+B) Always Below 1 Ω
      5 (IGT/INJ relay) or C1-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
      5 (IGT/INJ relay) or C2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
      5 (IGT/INJ relay) or C3-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
      5 (IGT/INJ relay) or C4-1 (+B) - Body ground and other terminals Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - IGT/INJ RELAY) 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals