Operation Check [10/2022 - ]
WARNING: This page is about a different car, the 2025 Toyota Highlander, 2024 Toyota Highlander, and 2023 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
- CHECK WARNING AND INDICATOR LIGHT ILLUMINATION (for HV Model)
- Initial Check
- Turn the ignition switch off.
- Turn the ignition switch to ON (IG) or ON (READY).
- Check the operation of the following warning and indicator lights.
- SRS warning light
- EPS warning light
- MIL (Check engine warning light)
- Brake warning light/red (malfunction)
- Brake warning light/yellow (minor malfunction)
- Brake hold standby indicator light
- Brake hold operated indicator light
- ABS warning light
- VSC OFF indicator light
- Slip indicator light
- Tire pressure warning light
- PCS warning light
- Clearance sonar OFF indicator light
- PKSB OFF indicator light
- BSM OFF indicator light
OK
Vehicle Condition Warning/Indicator Lights Condition Ignition switch off → ignition switch ON (IG) → ignition switch ON (READY) Illuminates and turns off in either of the following patterns depending on the specification: - Illuminates when the ignition switch is turned to ON (IG), and turns off after a certain amount of seconds has elapsed*
- Illuminates when the ignition switch is turned to ON (IG), and turns off when the ignition switch is turned to ON (READY)
Ignition switch off → ignition switch ON (READY) Illuminates when the ignition switch is turned to ON (READY), and turns off after a certain amount of seconds has elapsed* *: The amount of seconds until turning off differs depending on each indicator or warning light.
- Initial Check
- CHECK WARNING AND INDICATOR LIGHT ILLUMINATION (for Gasoline Model)
- Initial Check
- Turn the ignition switch off.
- Turn the ignition switch to ON.
- Check the operation of the following warning and indicator lights.
- SRS warning light
- EPS warning light
- MIL (Check engine warning light)
- Brake warning light/red (malfunction)
- Brake warning light/yellow (minor malfunction)
- Brake hold standby indicator light
- Brake hold operated indicator light
- ABS warning light
- VSC OFF indicator light
- Slip indicator light
- Tire pressure warning light
- Stop and start off indicator light (w/ Stop and Start System)
- Stop and start indicator light (w/ Stop and Start System)
- Eco driving indicator light
- PCS warning light
- Clearance sonar OFF indicator light
- PKSB OFF indicator light
- BSM OFF indicator light
- Downhill assist control indicator light
OK
Vehicle Condition Warning/indicator Lights Condition Ignition switch off → ignition switch ON Illuminates and turns off in either of the following patterns depending on the specification: - Illuminates when the ignition switch is turned to ON, and turns off after a certain amount of seconds has elapsed*
- Illuminates when the ignition switch is turned to ON, and turns off after the engine starts
*: The amount of seconds until turning off differs depending on each indicator or warning light.
- Initial Check
- CHECK SPEEDOMETER NOTE:
- If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
- When the electronically controlled brake system is malfunctioning, an accurate vehicle speed signal may not be able to be obtained. Therefore, make sure to confirm that the electronically controlled brake system is not malfunctioning before performing this procedure.
HINT:
The indicated value of the speedometer has an allowable range. Therefore, even when the combination meter assembly is not malfunctioning, the actual vehicle speed and the indicated value speed may not match.
- Read the vehicle speed of the Data List item of the electronically controlled brake system and compare the indicated values of the speedometer with the following table.REFERENCE (FOR SPEEDOMETER WITH IMPERIAL UNITS FOR MAIN SCALE):
Data List: vehicle speed value (km/h) Acceptable Range (km/h) 20 18.5 to 22.5 40 38.7 to 43.2 60 59.2 to 63.7 80 79.3 to 84.3 100 99.8 to 104.8 120 120.2 to 125.3 140 140.7 to 145.7 160 161.2 to 166.2 180 181.6 to 186.6 200 202.1 to 207.1 REFERENCE (FOR SPEEDOMETER WITH IMPERIAL UNITS FOR MAIN SCALE):Data List: vehicle speed value (mph) Acceptable Range (mph) 20 19.3 to 21.8 40 39.5 to 42.3 60 60.0 to 62.8 80 80.2 to 83.4 100 100.7 to 103.9 120 121.1 to 124.3 OK
Speedometer reading is within the acceptable range at each vehicle speed.
- CHECK TACHOMETER (for Gasoline Model) NOTE:
When the SFI system is malfunctioning, an accurate engine speed signal may not be able to be obtained. Therefore, make sure to confirm that the SFI system is not malfunctioning before performing this procedure.
HINT:
The indicated value of the tachometer has an allowable range. Therefore, even when the combination meter assembly is not malfunctioning, the actual engine speed and the indicated value speed may not match.
- Read the engine speed of the Data List item of the SFI system and compare the indicated values of the tachometer with the following table.
Data List: engine speed value (rpm) Acceptable Range (rpm) 700 630 to 770 1000 (900 to 1100) 2000 (1850 to 2150) 3000 2800 to 3200 4000 (3800 to 4200) 5000 4800 to 5200 6000 (5750 to 6250) 7000 6700 to 7300 () is for Reference
OK
Tachometer reading is within the acceptable range at each engine speed.
- Read the engine speed of the Data List item of the SFI system and compare the indicated values of the tachometer with the following table.