DTC P0351-13: Ignition Coil "A" Circuit Open; DTC P0352-13: Ignition Coil "B" Circuit Open; DTC P0353-13: Ignition Coil "C" Circuit Open; DTC P0354-13: Ignition Coil "D" Circuit Open [01/2019 - 04/2020]: Procedure
WARNING: This page is about a different variant/trim than selected.
- CLEAR DTC
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs.
Powertrain > Engine > Clear DTCs
- Turn the power switch off and wait for at least 30 seconds.
Result
Proceed to NEXT
Result:
NEXT
See step 2
- CHECK WHETHER DTC OUTPUT RECURS (DTC P0351-13, P0352-13, P0353-13 OR P0354-13)
- Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).NOTE:
Do not change the location of the connectors.
- Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
- Enter the following menus: Powertrain / Engine / Trouble Codes.
- Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
Result Proceed to Same DTC output A Different ignition coil DTC output B HINT:
Perform "Inspection After Repair" after replacing the ignition coil assembly.
Refer to INITIALIZATION [01/2019 - 09/2022]
Result:
B
REPLACE IGNITION COIL ASSEMBLY. Refer to REMOVAL [01/2019 - 09/2022]
Result:
A
See step 3
- Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).
- CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
*a Front view of wire harness connector
(to Ignition Coil Assembly)- Disconnect the ignition coil assembly connector.
- Turn the power switch on (IG).
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition C2-1 (+B) - Body ground Power switch on (IG) 11 to 14 V C4-1 (+B) - Body ground Power switch on (IG) 11 to 14 V C6-1 (+B) - Body ground Power switch on (IG) 11 to 14 V C8-1 (+B) - Body ground Power switch on (IG) 11 to 14 V Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - IGNITION COIL ASSEMBLY)
Result:
OK
See step 4
- CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
- Disconnect the ignition coil assembly connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition C2-4 (GND) - Body ground Always Below 1 Ω C4-4 (GND) - Body ground Always Below 1 Ω C6-4 (GND) - Body ground Always Below 1 Ω C8-4 (GND) - Body ground Always Below 1 Ω Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 5
- CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
- Disconnect the ignition coil assembly connector.
- Disconnect the ECM connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition C2-2 (IGF) - C77-71 (IGF1) Always Below 1 Ω C4-2 (IGF) - C77-71 (IGF1) Always Below 1 Ω C6-2 (IGF) - C77-71 (IGF1) Always Below 1 Ω C8-2 (IGF) - C77-71 (IGF1) Always Below 1 Ω C2-3 (IGT1) - C77-75 (IGT1) Always Below 1 Ω C4-3 (IGT2) - C77-74 (IGT2) Always Below 1 Ω C6-3 (IGT3) - C77-73 (IGT3) Always Below 1 Ω C8-3 (IGT4) - C77-72 (IGT4) Always Below 1 Ω C2-2 (IGF) or C77-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher C4-2 (IGF) or C77-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher C6-2 (IGF) or C77-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher C8-2 (IGF) or C77-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher C2-3 (IGT1) or C77-75 (IGT1) - Body ground and other terminals Always 10 kΩ or higher C4-3 (IGT2) or C77-74 (IGT2) - Body ground and other terminals Always 10 kΩ or higher C6-3 (IGT3) or C77-73 (IGT3) - Body ground and other terminals Always 10 kΩ or higher C8-3 (IGT4) or C77-72 (IGT4) - Body ground and other terminals Always 10 kΩ or higher Result
Proceed to OK NG
Result:
OK
REPLACE ECM. Refer to REMOVAL [01/2019 - 04/2020]
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR