LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> Corolla L >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 71 (Engine Cooling System (M20A-FKS) - Service Information) >> COOLING FAN MOTOR (w/o Cooling Fan ECU) >> Removal [09/2022 - 11/2022] >> Procedure

Removal [09/2022 - 11/2022]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 9

  2. DRAIN ENGINE COOLANT (for Fully Sealed Type) 

    Refer to PROCEDURE - Step 1

  3. DRAIN ENGINE COOLANT (for Non-Fully Sealed Type) 

    Refer to PROCEDURE - Step 2

  4. REMOVE HEADLIGHT ASSEMBLY 

    Refer to REMOVAL [09/2022 - ]

  5. REMOVE INLET NO. 3 AIR CLEANER 
    1. Remove the 2 clips.
      GTY925481Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the claw to remove the inlet No. 3 air cleaner.
  6. REMOVE INLET NO. 1 AIR CLEANER 
    1. Remove the 4 bolts and inlet No. 1 air cleaner from the upper radiator support sub-assembly and inlet No. 2 air cleaner.
      GTY925480Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE INLET NO. 2 AIR CLEANER 
    1. Remove the inlet No. 2 air cleaner from the air cleaner case sub-assembly.
      GTY925479Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE HOOD LOCK ASSEMBLY 

    Refer to PROCEDURE - Step 5

  9. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY 
    1. Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.
      GTY858600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the horn connector.
      GTY926236Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 3 clamps to disconnect the wire harness from the upper radiator support sub-assembly.
      GTY925441Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 5 bolts and upper radiator support sub-assembly.
      GTY925439Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. DISCONNECT NO. 2 WATER BY-PASS HOSE (for Fully Sealed Type) 
    1. Disengage the 5 clamps to disconnect the No. 2 water by-pass hose from the radiator assembly and fan shroud.
      GTY925492Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. DISCONNECT NO. 1 RADIATOR HOSE 
    1. Disengage the clamp and disconnect the No. 1 radiator hose from the hose clamp.
      GTY945453Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. DISCONNECT NO. 2 RADIATOR HOSE 
    1. Disengage the clamp and disconnect the No. 2 radiator hose from the hose clamp.
      GTY925478Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE NO. 2 RADIATOR AIR GUIDE 
    1. Disengage the 5 claws to remove the No. 2 radiator air guide.
      GTY925490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE FAN WITH MOTOR ASSEMBLY 
    1. Disconnect the cooling fan motor connector.
      GTY864482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Lock Lever
      1. Disengage the claw and raise the lock lever to disconnect the cooling fan motor connector as shown in the illustration.
        NOTE:

        After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector.

    2. Disengage the 2 wire harness clamps.
    3. Disengage the 2 claws.
      GTY945455Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disengage the 2 guides to remove the fan with motor assembly from the radiator assembly.
      NOTE:

      Do not damage the radiator assembly when removing the fan with motor assembly.

  15. REMOVE FAN 
    1. Remove the 3 screws and fan from the cooling fan motor.
      GTY823767Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE COOLING FAN MOTOR 
    1. Remove the 3 screws and cooling fan motor from the fan shroud.
      GTY837955Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals