Components [06/2018 - 06/2021]
WARNING: This page is about a different variant/trim than selected.
Fig 1: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (1 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | OUTER COWL TOP PANEL SUB-ASSEMBLY | *2 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL |
| Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N.m (kgf/cm, ft.lbf) | N.m (kgf/cm, ft.lbf): Specified torque |
Fig 2: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (2 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | BATTERY CLAMP SUB-ASSEMBLY | - | - |
| N.m (kgf/cm, ft.lbf): Specified torque | - | - |
Fig 3: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (3 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *A | Type A | *B | Type B |
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| N.m (kgf/cm, ft.lbf): Specified torque | - | - |
Fig 4: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (4 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | FRONT FLOOR CENTER BRACE | *2 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
| *3 | COMPRESSION SPRING | *4 | GASKET |
| N.m (kgf/cm, ft.lbf): Specified torque | • | Non-reusable part |
Fig 5: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (5 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | WIRE HARNESS | *2 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N.m (kgf/cm, ft.lbf) | N.m (kgf/cm, ft.lbf): Specified torque | ||
| • | Non-reusable part | - | - |
Fig 6: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (6 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | FUEL DELIVERY GUARD | *2 | INLET HOSE |
| *3 | COLUMN HOLE COVER SILENCER SHEET | *4 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
| *5 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | - | - |
| Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N.m (kgf/cm, ft.lbf) | N.m (kgf/cm, ft.lbf): Specified torque |
Fig 7: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (7 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *2 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
| *3 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH | - | - |
| Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N.m (kgf/cm, ft.lbf) | N.m (kgf/cm, ft.lbf): Specified torque |
Fig 8: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (8 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY | *2 | MANIFOLD STAY |
| N.m (kgf/cm, ft.lbf): Specified torque | - | - |
Fig 9: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (9 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | ENGINE ASSEMBLY | *2 | MANUAL TRANSAXLE ASSEMBLY |
| *3 | NO. 2 ENGINE MOVING CONTROL ROD | *4 | ENGINE MOUNTING BRACKET LH |
| *5 | ENGINE MOUNTING STAY LH | *6 | ENGINE MOUNTING INSULATOR LH |
| *7 | NO. 1 CLUTCH HOSE | - | - |
| Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N.m (kgf/cm, ft.lbf) | N.m (kgf/cm, ft.lbf): Specified torque | ||
| • | Non-reusable part | - | - |
Fig 10: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (10 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY TO BLEEDER TUBE | *2 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
| *3 | BLEEDER TO FLEXIBLE HOSE TUBE | *4 | CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY |
| *5 | CLAMP | - | - |
| Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N.m (kgf/cm, ft.lbf) | N.m (kgf/cm, ft.lbf): Specified torque | ||
| * | For use with union nut wrench | • | Non-reusable part |
| Clutch spline grease | * | Precoated part |
Fig 11: Manual Transaxle Assembly Replacement Components With Torque Specifications [06/2018 - 06/2021] (11 Of 11)
| Callout | Description | Callout | Description |
|---|---|---|---|
| *1 | CLUTCH FLEXIBLE HOSE BRACKET | *2 | CONTROL CABLE BRACKET ASSEMBLY |
| *3 | TRANSMISSION CASE PLUG ASSEMBLY | *4 | WIRE HARNESS CLAMP BRACKET |
| N.m (kgf/cm, ft.lbf): Specified torque | • | Non-reusable part | |
| Gear oil | - | - |