DTC P0365-31: Camshaft Position Sensor "B" Bank 1 No Signal [06/2018 - 03/2019]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine / Trouble Codes.
5. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTC P0365-31 is output	A
   DTC P0365-31 and P0365-11 or P0365-15 are output	B

   HINT: 

   • If DTC P0365-11or P0365-15 is output, perform troubleshooting for it first.

Result: 

B 

GO TO DTC CHART 

Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2018 - 01/2019] , or refer to DIAGNOSTIC TROUBLE CODE CHART [01/2019 - 03/2019]

Result: 

A 

See step  2

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.

1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
2. Turn the engine switch on (IG).
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   C11-3 (VC2) - Body ground	Engine switch on (IG)	4.5 to 5.5 V
   C11-1 (VVE+) - Body ground	Engine switch on (IG)	3.0 to 5.0 V

4. Turn the engine switch off.
5. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C11-2 (VVE-) - Body ground	Engine switch off	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  5

Result: 

OK 

See step  3

1. Remove the camshaft position sensor (for exhaust camshaft).

   Refer to REMOVAL [06/2018 - ]

2. Confirm that there is no oil on the connecting parts of the camshaft position sensor (for exhaust camshaft) connector.

   OK

   There is no oil on the connecting parts of the camshaft position sensor (for exhaust camshaft).

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) 

Refer to REMOVAL [06/2018 - ]

Result: 

OK 

See step  4

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   3 (VC2) - 1 (VVE+)	Always	10 kΩ or higher
   3 (VC2) - 2 (VVE-)	Always	10 kΩ or higher
   1 (VVE+) - 2 (VVE-)	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE ECM 

Refer to REMOVAL [06/2018 - 01/2019] , or refer to REMOVAL [01/2019 - 03/2019]

Result: 

NG 

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) 

Refer to REMOVAL [06/2018 - ]

1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
2. Disconnect the ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C11-3 (VC2) - C76-113 (VCE1)	Always	Below 1 Ω
   C11-1 (VVE+) - C76-91 (EV1+)	Always	Below 1 Ω
   C11-2 (VVE-) - C76-114 (EV1-)	Always	Below 1 Ω
   C11-3 (VC2) or C76-113 (VCE1) - Body ground and other terminals	Always	10 kΩ or higher
   C11-1 (VVE+) or C76-91 (EV1+) - Body ground and other terminals	Always	10 kΩ or higher
   C11-2 (VVE-) or C76-114 (EV1-) - Body ground and other terminals	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE ECM 

Refer to REMOVAL [06/2018 - 01/2019] , or refer to REMOVAL [01/2019 - 03/2019]

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR