DTC P012F-62: Engine Coolant Temperature/Engine Oil Temperature Signal Compare Failure [03/2019 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine / Trouble Codes.
5. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTC P012F-62 is output	A
   DTC P012F-62 and other DTCs are output	B

   HINT: 

   If any DTCs other than P012F-62 are output, troubleshoot those DTCs first.

6. Record the freeze frame data.

Result: 

B 

GO TO DTC CHART 

Refer to DIAGNOSTIC TROUBLE CODE CHART [03/2019 - 09/2019] , or refer to DIAGNOSTIC TROUBLE CODE CHART [09/2019 - 04/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [04/2020 - 06/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [06/2020 - 06/2021] , or refer to DIAGNOSTIC TROUBLE CODE CHART [06/2021 - 09/2022] , or refer to DIAGNOSTIC TROUBLE CODE CHART [09/2022 - 11/2022] , or refer to DIAGNOSTIC TROUBLE CODE CHART [11/2022 - 03/2023] , or refer to DIAGNOSTIC TROUBLE CODE CHART [03/2023 - 09/2024] , or refer to DIAGNOSTIC TROUBLE CODE CHART [09/2024 - ]

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Using the Techstream, read the values displayed in the freeze frame data recorded in step 1.

   Powertrain > Engine > DTC (P012F-62) > Freeze Frame Data 

   Tester Display
   Coolant Temperature
   Intake Air Temperature

5. Read the value displayed on the Techstream.

   Standard

   Techstream Display	Specified Condition
   Difference between the Coolant Temperature and the Intake Air Temperature	Within 15°C (27°F)

   HINT: 

   • When the engine is cold, the value of the engine coolant temperature, engine oil temperature and intake air temperature should be approximately the same.
   • If the result is not as specified, check that there are no heat sources such as a block heater in the engine compartment.
   • Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

     Refer to INITIALIZATION [06/2018 - 09/2019] , or refer to INITIALIZATION [09/2019 - 04/2020] , or refer to INITIALIZATION [04/2020 - 11/2022] , or refer to INITIALIZATION [11/2022 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE ENGINE COOLANT TEMPERATURE SENSOR 

Refer to REMOVAL [03/2019 - 09/2019] , or refer to REMOVAL [09/2019 - 09/2022] , or refer to REMOVAL [09/2022 - 11/2022] , or refer to REMOVAL [11/2022 - 03/2023] , or refer to REMOVAL [03/2023 - 09/2024] , or refer to REMOVAL [09/2024 - ]

Result: 

OK 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Using the Techstream, read the values displayed in the freeze frame data recorded in step 1.

   Powertrain > Engine > DTC (P012F-62) > Freeze Frame Data 

   Tester Display
   Engine Oil Temperature Sensor
   Intake Air Temperature

5. Read the value displayed on the Techstream.

   Standard

   Techstream Display	Specified Condition
   Difference between the Engine Oil Temperature Sensor and the Intake Air Temperature	Within 15°C (27°F)

   HINT: 

   When the engine is cold, the value of the engine coolant temperature, engine oil temperature and intake air temperature should be approximately the same.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE ECM 

Refer to REMOVAL [03/2019 - 09/2022] , or refer to REMOVAL [09/2022 - 11/2022] , or refer to REMOVAL [11/2022 - 03/2023] , or refer to REMOVAL [03/2023 - 09/2024] , or refer to REMOVAL [09/2024 - ]

Result: 

NG 

REPLACE OIL PRESSURE AND TEMPERATURE SENSOR 

Refer to REMOVAL [06/2018 - ]