DTC C2198: Initialization Switch Error (for Test Diagnosis) [04/2018 -]: Procedure

1. Remove the steering pad switch assembly.

   Refer to REMOVAL [04/2018 - 08/2021] , or refer to REMOVAL [08/2021 -]

2. Inspect the steering pad switch assembly.

   Refer to INSPECTION [04/2018 -]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE STEERING PAD SWITCH ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 -] 

Result: 

OK 

See step  2

1. Remove the spiral cable sub-assembly.

   Refer to REMOVAL [04/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 -]

2. Inspect the spiral cable sub-assembly.

   Refer to INSPECTION [04/2018 -]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SPIRAL CABLE SUB-ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 -] 

Result: 

OK 

See step  3

1. Disconnect the G17 spiral cable sub-assembly connector.
2. Disconnect the G16 combination meter assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G17-10 (+DP2) - G16-28 (MSM+)	Always	Below 1 Ω
   G17-10 (+DP2) or G16-28 (MSM+) - Body ground	Always	10 kΩ or higher
   G17-11 (+DP) - G16-29 (MSTI)	Always	Below 1 Ω
   G17-11 (+DP) or G16-29 (MSTI) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  4

1. Disconnect the K11 tire pressure warning ECU and receiver connector.
2. Disconnect the G16 combination meter assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   K11-3 (CLSW) - G16-4 (INT)	Always	Below 1 Ω
   K11-3 (CLSW) or G16-4 (INT) - Body ground	Always	10 kΩ or higher
   G16-21 (ES) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  5

1. Connect the K11 tire pressure warning ECU and receiver connector.
2. Disconnect the G16 combination meter assembly connector.
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   G16-4 (INT) - Body ground	Power switch on (IG)	8 to 15 V

   Result

   Proceed to
   OK
   NG

Result: 

OK 

GO TO METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [04/2018 -] 

Result: 

NG 

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER. Refer to  REMOVAL [04/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 -]