Component Operating Range
WARNING: This page is about a different variant/trim than selected.
C139A
| All of the following conditions are met | - |
| Power switch | Off |
| History of vehicle speed in this trip | Higher than 3 km/h (2 mph) |
| Reaction force pressure sensor fail | Not detected |
| Servo pressure sensor fail | Not detected |
| Brake-by-wire controlled mode | On |
| Brake fluid temperature | Higher than 0°C (32°F) |
| Reaction force pressure | 4.5 MPa (45.9 kgf/cm2 , 653 psi) or more for less than 0.003 seconds |
| Reaction force pressure | 1.5 MPa (15.3 kgf/cm2 , 218 psi) or more for less than 0.5 seconds |
C139D
| All of the following conditions are met | - |
| Servo pressure sensor fail | Not detected |
| Brake-by-wire controlled mode | On |
| Brake | On |
| Servo pressure | Higher than 0.1 MPa (1 kgf/cm2 , 15 psi) |
C13CD
| All of the following conditions are met | - |
| Servo pressure sensor fail | Not detected |
| Brake-by-wire controlled mode | On |
| Brake | On |
| Servo pressure | 0.5 MPa (5.1 kgf/cm2 , 73 psi) or more |
| Malfunction criteria | Not met |
C13CE
| All of the following conditions are met | - |
| Servo pressure sensor fail | Not detected |
| Brake-by-wire controlled mode | On |
| Servo pressure decreases after linear solenoid (SLR) on | Higher than 0.5 MPa (5.1 kgf/cm2 , 73 psi) |
| Malfunction criteria | Not met |
C1400
| All of the following conditions are met | A, B, C, D, E, F and G |
| A. Power switch | Off |
| B. History of vehicle speed in this trip | Higher than 3 km/h (2 mph) |
| C. Reaction force pressure sensor fail | Not detected |
| D. Servo pressure sensor fail | Not detected |
| E. Brake-by-wire controlled mode | On |
| F. Brake fluid temperature | Higher than 0°C (32°F) |
| G. Any of the following conditions are met | (a), (b), (c) or (d) |
| (a). Servo pressure decrease | 0.4 MPa (4.1 kgf/cm2 , 58 psi) or less for 2 seconds or more |
| (b). Gradient of servo pressure | -20 MPa/s or more for 2 seconds or more |
| (c). Servo pressure increase after ABS pump motor on after malfunction criteria (a) and (b) are met | Higher than 0.5 MPa (5.1 kgf/cm2 , 73 psi) for less than 0.051 seconds |
| (d). Reduction of time required to ABS pump motor voltage drop below 1.3 V at ABS pump motor voltage on to off compared with no load condition after malfunction criteria (a) and (b) are met | Less than 0.1 seconds |
C14EE AND C14F7
| All of the following conditions are met | A, B, C, D, E, F and G |
| A. Power switch | Off |
| B. History of vehicle speed in this trip | Higher than 3 km/h (2 mph) |
| C. Reaction force pressure sensor fail | Not detected |
| D. Servo pressure sensor fail | Not detected |
| E. Brake-by-wire controlled mode | On |
| F. Brake fluid temperature | Higher than 0°C (32°F) |
| G. Either of the following condition is met | a or b |
| a. Both of the following conditions are met | - |
| Reaction force pressure decrease (a) | 0.03 MPa (0.3 kgf/cm2 , 4.4 psi) or more for less than 6 seconds |
| Reaction force pressure (b) | Less than -0.6 MPa (-6.1 kgf/cm2 , -87 psi) for less than 6 seconds |
| b. Reaction force pressure after malfunction criteria (b) is met | 0.2 MPa (2 kgf/cm2 , 29 psi) or more for less than 1.5 seconds |