LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> Avalon Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 26 (Automatic Transmission (Service Information) [UB80F]) >> Oil Cooler >> Removal [08/2020 - ] >> Procedure

Removal [08/2020 - ]: Procedure

WARNING: This page is about a different car, the 2021 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE BATTERY 

    Refer to REMOVAL [08/2020 - ]

  2. REMOVE ECM 

    Refer to REMOVAL [08/2020 - ]

  3. REMOVE BATTERY CLAMP SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 25

  4. REMOVE FRONT WHEEL LH 

    Refer to REMOVAL [04/2018 - ]

  5. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 8

  6. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 9

  7. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10

  8. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11

  9. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 12

  10. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 1

  11. DRAIN AUTOMATIC TRANSAXLE FLUID 

    See step  7

  12. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE 
    1. Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.
      GTY865170Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.

  13. DISCONNECT INLET NO. 1 OIL COOLER HOSE 
    1. Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.
      GTY932123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.

  14. REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE 
    1. Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.
      GTY865172Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.
      GTY762233Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.

    3. Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.
      GTY762231Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.

    4. Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.
      GTY928259Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Oil Cooler Tube Sub-assembly without Hose
      *2 Inlet No. 1 Oil Cooler Hose
      *3 Inlet No. 2 Oil Cooler Hose
      *4 Outlet No. 1 Oil Cooler Hose
      *5 Outlet No. 2 Oil Cooler Hose
  15. DISCONNECT NO. 1 WATER BY-PASS HOSE 
    1. Disengage the 3 clamps to remove the transmission breather clamp.
      GTY958209Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.
      GTY869902Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.

  16. DISCONNECT WATER BY-PASS HOSE ASSEMBLY 
    1. Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.
      GTY933164Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.

  17. REMOVE TRANSMISSION OIL COOLER 
    1. Remove the 3 bolts and transmission oil cooler from the automatic transaxle case sub-assembly.
      GTY865164Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.

scientia non olet · About LEMON Manuals