LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2020 >> Avalon Limited >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Audio / Video System - Diagnostic Codes & Symptom Tests (Except Hybrid) >> AUDIO AND VISUAL SYSTEM (for Gasoline Model) >> DTC B15C3: Speaker Output Short [04/2018 - 08/2019] >> Procedure

DTC B15C3: Speaker Output Short [04/2018 - 08/2019]: Procedure

  1. CHECK MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for 8 Speakers (w/ Manual (SOS) Switch) A
      for 8 Speakers (w/o Manual (SOS) Switch) B
      for 14 Speakers C

    Result: 

    B 

    See step  5

    Result: 

    C 

    See step  12

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) 
    1. Disconnect the G14 radio and display receiver assembly connector.
    2. Disconnect the G9 DCM (telematics transceiver) connector.
    3. Disconnect the G7 front No. 2 speaker assembly LH connector.
    4. Disconnect the J3 and J4 rear No. 2 speaker assembly connectors.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G14-1 (FR+) or G9-2 (SPI+) - Body ground Always 10 kΩ or higher
      G14-6 (FR-) or G9-3 (SPI-) - Body ground Always 10 kΩ or higher
      G14-2 (FL+) or G7-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-7 (FL-) or G7-2 (-TW) - Body ground Always 10 kΩ or higher
      G14-4 (RR+) or J3-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-9 (RR-) or J3-2 (-TW) - Body ground Always 10 kΩ or higher
      G14-3 (RL+) or J4-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-8 (RL-) or J4-2 (-TW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND) 
    1. Disconnect the G9 DCM (telematics transceiver) connector.
    2. Disconnect the G6 front No. 2 speaker assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G9-5 (SPO+) or G6-4 (+TW) - Body ground Always 10 kΩ or higher
      G9-6 (SPO-) or G6-2 (-TW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [04/2018 - 08/2020]

    2. Measure the resistance according to the value(s) in the table below.
      GTY450683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  6

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [04/2018 - 08/2020] 

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR SPEAKERS - BODY GROUND) 
    1. Disconnect the G14 radio and display receiver assembly connector.
    2. Disconnect the G6 and G7 front No. 2 speaker assembly connectors.
    3. Disconnect the J3 and J4 rear No. 2 speaker assembly connectors.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G14-1 (FR+) or G6-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-6 (FR-) or G6-2 (-TW) - Body ground Always 10 kΩ or higher
      G14-2 (FL+) or G7-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-7 (FL-) or G7-2 (-TW) - Body ground Always 10 kΩ or higher
      G14-4 (RR+) or J3-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-9 (RR-) or J3-2 (-TW) - Body ground Always 10 kΩ or higher
      G14-3 (RL+) or J4-4 (+TW) - Body ground Always 10 kΩ or higher
      G14-8 (RL-) or J4-2 (-TW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the I1 and I15 front No. 1 speaker assembly connectors.
    2. Disconnect the G6 and G7 front No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I1-2 or G6-3 (+) - Body ground Always 10 kΩ or higher
      I1-1 or G6-1 (-) - Body ground Always 10 kΩ or higher
      I15-2 or G7-3 (+) - Body ground Always 10 kΩ or higher
      I15-1 or G7-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY OR REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the J1 and J2 rear speaker assembly connectors.
    2. Disconnect the J3 and J4 rear No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J1-1 or J3-1(-) - Body ground Always 10 kΩ or higher
      J1-2 or J3-3 (+) - Body ground Always 10 kΩ or higher
      J2-1 or J4-1 (-) - Body ground Always 10 kΩ or higher
      J2-2 or J4-3 (+) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [04/2018 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

    Result: 

    OK 

    See step  9

  9. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [04/2018 - 08/2019]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

    Result: 

    OK 

    See step  10

  10. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [04/2018 -]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  11

  11. REPLACE REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the rear No. 2 speaker assembly.

      Refer to INSPECTION [04/2018 - 08/2019]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

  12. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) 
    1. Disconnect the G10 stereo component amplifier assembly connector.
    2. Disconnect the G9 DCM (telematics transceiver) connector.
    3. Disconnect the G70 and G71 front No. 2 speaker assembly connectors.
    4. Disconnect the G72 front No. 4 speaker assembly connector.
    5. Disconnect the G79 front No. 3 speaker assembly LH connector.
    6. Disconnect the J3 and J4 rear No. 2 speaker assembly connectors.
    7. Disconnect the K2 and K3 speaker assembly with bracket connectors.
    8. Disconnect the K1 rear No. 3 speaker assembly connector.
    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G10-9 (TWR+) or G70-2 - Body ground Always 10 kΩ or higher
      G10-24 (TWR-) or G70-1 - Body ground Always 10 kΩ or higher
      G10-8 (TWL+) or G71-2 - Body ground Always 10 kΩ or higher
      G10-23 (TWL-) or G71-1 - Body ground Always 10 kΩ or higher
      G10-13 (FR+) or G9-2 (SPI+) - Body ground Always 10 kΩ or higher
      G10-28 (FR-) or G9-3 (SPI-) - Body ground Always 10 kΩ or higher
      G10-12 (FL+) or G79-4 (+TW) - Body ground Always 10 kΩ or higher
      G10-27 (FL-) or G79-2 (-TW) - Body ground Always 10 kΩ or higher
      G10-15 (RR+) or J3-4 (+TW) - Body ground Always 10 kΩ or higher
      G10-30 (RR-) or J3-2 (-TW) - Body ground Always 10 kΩ or higher
      G10-14 (RL+) or J4-4 (+TW) - Body ground Always 10 kΩ or higher
      G10-29 (RL-) or J4-2 (-TW) - Body ground Always 10 kΩ or higher
      G10-6 (WF1+) or K1-4 (WF1+) - Body ground Always 10 kΩ or higher
      G10-21 (WF1-) or K1-3 (WF1-) - Body ground Always 10 kΩ or higher
      G10-5 (WF2+) or K1-2 (WF2+) - Body ground Always 10 kΩ or higher
      G10-20 (WF2-) or K1-1 (WF2-) - Body ground Always 10 kΩ or higher
      G10-7 (CTR+) or G72-2 - Body ground Always 10 kΩ or higher
      G10-22 (CTR-) or G72-1 - Body ground Always 10 kΩ or higher
      G10-11 (SR+) or K2-2 - Body ground Always 10 kΩ or higher
      G10-26 (SR-) or K2-1 - Body ground Always 10 kΩ or higher
      G10-10 (SL+) or K3-2 - Body ground Always 10 kΩ or higher
      G10-25 (SL-) or K3-1 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  13

  13. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND) 
    1. Disconnect the G9 DCM (telematics transceiver) connector.
    2. Disconnect the G78 front No. 3 speaker assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G9-5 (SPO+) or G78-4 (+TW) - Body ground Always 10 kΩ or higher
      G9-6 (SPO-) or G78-2 (-TW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  14

  14. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [04/2018 - 08/2020]

    2. Measure the resistance according to the value(s) in the table below.
      GTY450683Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
      3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [04/2018 - 08/2020] 

    Result: 

    OK 

    See step  15

  15. CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 3 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the I1 and I15 front No. 1 speaker assembly connectors.
    2. Disconnect the G78 and G79 front No. 3 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I1-2 or G78-3 (+) - Body ground Always 10 kΩ or higher
      I1-1 or G78-1 (-) - Body ground Always 10 kΩ or higher
      I15-2 or G79-3 (+) - Body ground Always 10 kΩ or higher
      I15-1 or G79-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  16

  16. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY OR REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the J1 and J2 rear speaker assembly connectors.
    2. Disconnect the J3 and J4 rear No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J1-1 or J3-3 (+) - Body ground Always 10 kΩ or higher
      J1-2 or J3-1 (-) - Body ground Always 10 kΩ or higher
      J2-1 or J4-3 (+) - Body ground Always 10 kΩ or higher
      J2-2 or J4-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [04/2018 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

    Result: 

    OK 

    See step  18

  18. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [04/2018 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

    Result: 

    OK 

    See step  19

  19. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY 
    1. Remove the front No. 4 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the front No. 4 speaker assembly.

      Refer to INSPECTION [04/2018 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 4 SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

    Result: 

    OK 

    See step  20

  20. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [04/2018 - 08/2019]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 -] 

    Result: 

    OK 

    See step  21

  21. INSPECT SPEAKER ASSEMBLY WITH BRACKET 
    1. Remove the speaker assembly with bracket.

      Refer to REMOVAL [04/2018 - 08/2021]

    2. Inspect the speaker assembly with bracket.

      Refer to INSPECTION [04/2018 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SPEAKER ASSEMBLY WITH BRACKET. Refer to  REMOVAL [04/2018 - 08/2021] 

    Result: 

    OK 

    See step  22

  22. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 
    1. Remove the rear No. 3 speaker assembly.

      Refer to REMOVAL [04/2018 - 08/2021]

    2. Inspect the rear No. 3 speaker assembly.

      Refer to INSPECTION [04/2018 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2021] 

    Result: 

    OK 

    See step  23

  23. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the front No. 3 speaker assembly.

      Refer to INSPECTION [04/2018 -]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  24

  24. REPLACE REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly.

      Refer to REMOVAL [04/2018 -]

    2. Inspect the rear No. 2 speaker assembly.

      Refer to INSPECTION [04/2018 - 08/2019]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2021] 

scientia non olet · About LEMON Manuals