LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Sienna SE, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Automatic Transaxle System [UA80E] (Service Information)) >> Valve Body Assembly >> Inspection [08/2016 - ] >> Procedure

Inspection [08/2016 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSPECT SHIFT SOLENOID VALVE SL 
    1. Measure the resistance according to the value(s) in the table below.
      GTY663166Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Shift Solenoid Valve SL)

      Standard Resistance

      Tester Connection Condition Specified Condition
      Shift solenoid valve SL connector terminal - Shift solenoid valve SL body 20°C (68°F) 11 to 15 Ω

      If the result is not as specified, replace the shift solenoid valve SL.

    2. Connect a positive (+) lead from the battery to the terminal of the shift solenoid valve SL connector and a negative (-) lead to the shift solenoid valve SL body, and check that the shift solenoid valve SL moves and makes an operating sound.
      NOTE:

      When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

      OK

      The shift solenoid valve SL moves and makes an operating sound.

      If the result is not as specified, replace the shift solenoid valve SL.

  2. INSPECT SHIFT SOLENOID VALVE SLT 
    1. Measure the resistance according to the value(s) in the table below.
      GTY703694Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Shift Solenoid Valve SLT)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω

      If the result is not as specified, replace the shift solenoid valve SLT.

    2. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the shift solenoid valve SLT connector, and check that the shift solenoid valve SLT moves and makes an operating sound.
      NOTE:

      When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

      OK

      The shift solenoid valve SLT moves and makes an operating sound.

      If the result is not as specified, replace the shift solenoid valve SLT.

  3. INSPECT SHIFT SOLENOID VALVE SLU 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

  4. INSPECT SHIFT SOLENOID VALVE SL1 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

  5. INSPECT SHIFT SOLENOID VALVE SL2 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

  6. INSPECT SHIFT SOLENOID VALVE SL3 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

  7. INSPECT SHIFT SOLENOID VALVE SL4 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

  8. INSPECT SHIFT SOLENOID VALVE SL5 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

  9. INSPECT SHIFT SOLENOID VALVE SL6 

    HINT: 

    Refer to Inspect Shift Solenoid Valve SLT.

scientia non olet · About LEMON Manuals