LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Sienna SE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Automatic Transaxle System [U660E] (Service Information)) >> VALVE BODY ASSEMBLY(When Not Using the Engine Support Bridge) >> Installation [12/2015 - 08/2016] >> Procedure

Installation [12/2015 - 08/2016]: Procedure

WARNING: This page is about a different car, the 2016 Toyota Sienna. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL MANUAL VALVE 
    1. Coat the manual valve with ATF and install it into the transmission valve body.
  2. INSTALL TRANSAXLE CASE GASKET 
    1. Coat 2 new transaxle case gaskets with ATF.
    2. Install the 2 transaxle case gaskets onto the transaxle case.
  3. INSTALL TRANSMISSION VALVE BODY ASSEMBLY 
    1. Coat the O-ring of the transmission wire with ATF.
    2. Confirm that the manual valve lever is positioned as shown in the illustration and install the transmission valve body onto the automatic transaxle with the 11 bolts.
      GTY721062Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Positioning Bolt

      Torque: 11 N*m (110 kgf*cm, 8 ft.*lbf) 

      BOLT LENGTH

      Bolt Length mm (in.)
      A 25 (0.984)
      B 30 (1.18)
      C 35 (1.38)
      D 45 (1.77)
      E 55 (2.17)
      NOTE:
      • When installing the transmission valve body, be careful not to allow the transmission revolution sensor and automatic transaxle to interfere with each other.
      • Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.
      • First, temporarily tighten the bolts marked (*a) in the illustration because they are positioning bolts.
  4. INSTALL VALVE BODY OIL STRAINER ASSEMBLY 
    1. Coat a new O-ring with ATF and install it onto the valve body oil strainer.
    2. Install the valve body oil strainer onto the transmission valve body with the 2 bolts.
      GTY425039Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 11 N*m (110 kgf*cm, 8 ft.*lbf) 

  5. INSTALL TRANSMISSION OIL CLEANER MAGNET 
    1. Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan as shown in the illustration.
      GTY584961Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Oil Cleaner Magnet
  6. INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET 
    1. Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan.
  7. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY 
    1. Clean and degrease the bolt (*1) and the installation hole in the automatic transaxle.
      GTY726390Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Precoated Bolt
    2. Apply adhesive to 2 or 3 threads on the ends of the bolt (*1).

      Adhesive

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    3. Install the automatic transaxle oil pan with the transaxle oil pan gasket onto the automatic transaxle with the 18 bolts.

      Precoated Bolt (*1) 

      Torque: 7.0 N*m (71 kgf*cm, 62 in.*lbf) 

      except Precoated bolt 

      Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf) 

      NOTE:
      • In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install them within 10 minutes of adhesive application.
      • Completely remove any oil or grease from the contact surface of the automatic transaxle and automatic transaxle oil pan with the automatic transaxle oil pan gasket before installation.
  8. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY 

    See step  9

  9. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY 

    (Refer to INSTALLATION [12/2015 - 08/2016] )

scientia non olet · About LEMON Manuals