DTC P0745-7F: Pressure Control Solenoid "A" Actuator Stuck Off [08/2016 - 11/2017]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Transmission / Trouble Codes.
5. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   DTC P0745-7F and DTC P0740-7E, P0775-7F, P0795-7F, P08BA-7F, P2713-7F, P2807-7F and/or P2816-7F are output	A
   Only DTC P0745-7F is output	B
   DTCs other than P0745-7F, P0740-7E, P0775-7F, P0795-7F, P08BA-7F, P2713-7F, P2807-7F and P2816-7F are also output	C

   HINT: 

   • If any DTCs other than P0740-7E, P0745-7F, P0775-7F, P0795-7F, P08BA-7F, P2713-7F, P2807-7F and P2816-7F are output, perform troubleshooting for those DTCs first.
   • If a shift solenoid valve is stuck ON or OFF, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.

Result: 

B 

See step  3

Result: 

C 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - 11/2017] 

Result: 

A 

See step  2

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [08/2016 - ]

   HINT: 

   Write down the currently output DTCs before clearing them.

2. Perform the stall speed test.

   Refer to MECHANICAL SYSTEM TESTS [08/2016 - ]

   Result

   Test Condition	Proceed to
   Stall speed test can be performed	A
   Stall speed test cannot be performed	B

Result: 

B 

See step  5

Result: 

A 

See step  3

1. Remove the shift solenoid valves SL1, SL2, SL3, SL4, SL5 and SL6.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Shift Solenoid Valve SL1, SL2, SL3, SL4, SL5 and SL6)

   Refer to DISASSEMBLY [08/2016 - ]

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Shift solenoid valve SL1 connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω
   Shift solenoid valve SL2 connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω
   Shift solenoid valve SL3 connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω
   Shift solenoid valve SL4 connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω
   Shift solenoid valve SL5 connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω
   Shift solenoid valve SL6 connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω

3. Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

   OK

   Valve moves and makes an operating sound.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 SL5 OR SL6. Refer to  COMPONENTS [08/2016 - ] 

Result: 

OK 

See step  4

1. Remove the shift solenoid valve SL.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Shift Solenoid Valve SL

   Refer to DISASSEMBLY [08/2016 - ]

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Shift solenoid valve SL connector terminal - Shift solenoid valve SL body	20°C (68°F)	11 to 15 Ω

3. Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

   OK

   Valve moves and makes an operating sound.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SL. Refer to  COMPONENTS [08/2016 - ] 

Result: 

OK 

See step  5

1. Remove the shift solenoid valve SLT.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Shift Solenoid Valve SLT)

   Refer to DISASSEMBLY [08/2016 - ]

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Shift solenoid valve SLT connector terminal 1 - terminal 2	20°C (68°F)	5.0 to 5.6 Ω

3. Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead with a 21 W bulb to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

   OK

   Valve moves and makes an operating sound.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SLT. Refer to  COMPONENTS [08/2016 - ] 

Result: 

OK 

See step  6

1. Inspect the transmission valve body assembly.

   Refer to REMOVAL [08/2016 - ]

   OK

   There is no foreign matter on each valve and they operate smoothly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY. Refer to  COMPONENTS [08/2016 - ] 

Result: 

OK 

See step  7

1. Inspect the torque converter assembly.

   Refer to INSPECTION [08/2016 - ]

   OK

   The torque converter assembly is normal.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE TORQUE CONVERTER ASSEMBLY. Refer to  COMPONENTS [08/2016 - ] 

Result: 

OK 

See step  8

1. Repair or replace the automatic transaxle assembly.

   Refer to COMPONENTS [08/2016 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

PERFORM A/T CODE REGISTRATION. Refer to  REGISTRATION [08/2016 - ]