Speedometer Malfunction [12/2015 - ]: Procedure

1. Check if a CAN communication DTC is output (Refer to DIAGNOSIS SYSTEM [12/2015 - 08/2016] Refer to DIAGNOSIS SYSTEM [08/2016 - 11/2017] Refer to DIAGNOSIS SYSTEM [11/2017 - 08/2018] Refer to DIAGNOSIS SYSTEM [08/2018 - ] ).
   RESULT
   
   

   Result	Proceed to
   CAN communication DTC is not output	A
   CAN communication DTC is output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2015 - 08/2016]  Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2016 - 11/2017]  Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2017 - ] 

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
5. According to the display on the Techstream, perform the Active Test.
   COMBINATION METER
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Speed Meter Operation	Speedometer	OFF, 0, 40, 80, 120*1, 160*1	Operate with IG ON and the vehicle is stopped.
   			Acceptable range (km/h or mph): [Control range → Speedometer display] for mph 40 → 39.15 to 42.65 80 → 79.65 to 84.15 for km/h 40 → 38.95 to 42.95 80 → 78.9 to 84.9 120 → 119.8 to 125.8 160 → 159.8 to 167.8

   1. *1: except U.S.A.

   OK

   Speedometer indication is normal.

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY 

(Refer to REMOVAL [12/2015 - ] )

Result: 

OK 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Data List.
5. According to the display on the Techstream, read the Data List.
   COMBINATION METER
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Vehicle Speed Meter	Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)	Approximately same as actual vehicle speed (When vehicle is being driven)	-

   OK

   Vehicle speed displayed on the Techstream is almost the same as the speedometer indication.

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY 

(Refer to REMOVAL [12/2015 - ] )

Result: 

OK 

See step  4

1. Check if a vehicle stability control DTC is output (Refer to DTC CHECK / CLEAR [12/2015 - 11/2017] Refer to DTC CHECK / CLEAR [11/2017 - ] ).
   RESULT
   
   

   Result	Proceed to
   Vehicle stability control DTC is not output	A
   Vehicle stability control DTC is output	B

Result: 

A 

REPLACE COMBINATION METER ASSEMBLY 

(Refer to REMOVAL [12/2015 - ] )

Result: 

B 

GO TO VEHICLE STABILITY CONTROL SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2015 - 11/2017]  Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2017 - ]