SRS Warning Light Remains ON [08/2015 - 08/2017]: Procedure

1. Check if a CAN communication DTC is output (Refer to DIAGNOSIS SYSTEM [08/2015 - 08/2017] ).
   RESULT
   
   

   Result	Proceed to
   DTC is not output	A
   DTCs are output	B

Result: 

B 

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS 

(Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2017] )

Result: 

A 

See step  2

1. Measure the voltage of the battery.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   Battery	Always	11 to 14 V

Result: 

NG 

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM 

Result: 

OK 

See step  3

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Check that the connectors are properly connected to the center airbag sensor and combination meter.

   OK

   The connectors are properly connected.

Result: 

NG 

CONNECT CONNECTORS PROPERLY 

Result: 

OK 

See step  4

1. Disconnect the connectors from the center airbag sensor.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
3. Turn the ignition switch to ON.
4. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
5. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   H56-21 (IG2) - H56-25 (E1)	Ignition switch ON	11 to 14 V
   H56-21 (IG2) - H56-26 (E2)	Ignition switch ON	11 to 14 V

Result: 

NG 

REPLACE HARNESS AND CONNECTOR 

Result: 

OK 

See step  5

1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Disconnect the connector from the combination meter.
3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
4. Turn the ignition switch to ON.
5. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   H37-18 (B) - H37-40 (E1)	Always	11 to 14 V
   H37-20 (IG+) - H37-40 (E1)	Ignition switch ON	11 to 14 V

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  6

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Connect the connector to the combination meter.
4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
5. Turn the ignition switch to ON.
6. Check the SRS warning light condition.

   OK

   After the primary check period, SRS warning light goes off for approximately 10 seconds and remains on.

   HINT: 

   The primary check period is approximately 6 seconds after the ignition switch is turned to ON.

Result: 

OK 

REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

(Refer to REMOVAL [08/2015 - 08/2017] )

Result: 

NG 

REPLACE COMBINATION METER 

(Refer to PROBLEM SYMPTOMS TABLE [08/2015 - 08/2017] )