How To Proceed With Troubleshooting [08/2015 - ]: Procedure

Result

Result: 

NEXT 

See step  2

1. Refer to the How to Troubleshoot ECU Controlled Systems in "Introduction".

   Refer to

   HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - 08/2017]

   HOW TO PROCEED WITH TROUBLESHOOTING [08/2017 - 08/2018]

   HOW TO PROCEED WITH TROUBLESHOOTING [08/2018 - 08/2019]

   HOW TO PROCEED WITH TROUBLESHOOTING [08/2019 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

Standard Voltage

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result

Result: 

NEXT 

See step  4

Result

Result: 

NEXT 

See step  5

1. Refer to DTC Check/Clear.

   Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] , or refer to DTC CHECK / CLEAR [08/2019 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  6

Result

Result: 

NEXT 

See step  7

1. Refer to the Check Mode Procedure.

   Refer to CHECK MODE PROCEDURE [08/2015 - 08/2019] , or refer to CHECK MODE PROCEDURE [08/2019 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

1. Refer to the Road Test.

   Refer to ROAD TEST [08/2015 - ] 

   Result

   Result	Proceed to
   Symptom does not occur	A
   Symptom occurs	B

Result: 

B 

See step  10

Result: 

A 

See step  9

1. Refer to the Electronic Circuit Inspection Procedure.

   Refer to ELECTRONIC CIRCUIT INSPECTION PROCEDURE [08/2015 - 08/2019] , or refer to ELECTRONIC CIRCUIT INSPECTION PROCEDURE [08/2019 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Refer to DTC Check/Clear.

   Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] , or refer to DTC CHECK / CLEAR [08/2019 - ] 

   Result

   Result	Proceed to
   DTC is not output	A
   DTC is output	B

Result: 

B 

See step  18

Result: 

A 

See step  11

1. Refer to Park/Neutral Position Switch.

   Refer to ADJUSTMENT [08/2015 - ]

2. Refer to Shift Lever Assembly.

   Refer to ADJUSTMENT [08/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  21

Result: 

OK 

See step  12

1. Refer to the Mechanical System Tests.

   Refer to MECHANICAL SYSTEM TESTS [08/2015 - 08/2019] , or refer to MECHANICAL SYSTEM TESTS [08/2019 - ] 

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  17

Result: 

OK 

See step  13

1. Refer to the Hydraulic Test.

   Refer to HYDRAULIC TEST [08/2015 - 08/2019] , or refer to HYDRAULIC TEST [08/2019 - ] 

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  17

Result: 

OK 

See step  14

1. Refer to the Manual Shifting Test.

   Refer to MANUAL SHIFTING TEST [08/2015 - ] 

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  16

Result: 

OK 

See step  15

1. Refer to the Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [08/2015 - ] 

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  19

Result: 

OK 

See step  16

1. Refer to the Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [08/2015 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  17

Result

Result: 

NG 

See step  21

Result: 

OK 

See step  18

1. Refer to the Diagnostic Trouble Code Chart.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2017] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2017 - 08/2019] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - 09/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [09/2020 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  19

Result

Result: 

NEXT 

See step  20

Result

Result: 

NEXT 

See step  21

Result

Result: 

NEXT 

See step  22

Result

Result: 

NEXT 

END