DTC B15C1-11: GNSS Antenna Circuit Short to Ground; DTC B15C113: GNSS Antenna Circuit Open [08/2019 - ]: Procedure

1. Turn the engine switch off.
2. Connect the Techstream to the DLC3.
3. Turn the engine switch on (IG) and wait for 10 seconds or more.
4. Turn the Techstream on.
5. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [08/2019 - ]

6. Check for DTCs and check that no DTCs are output.

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [08/2019 - ] 

Result: 

NG 

See step  2

1. Disconnect the antenna connector from the Telephone and GPS antenna (for Roof Side).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (to Telephone and GPS antenna [for Roof Side])
   *b	Component without harness connected (to Roof Headlining Assembly [Roof Antenna Cord])

2. Disconnect the antenna connector from the roof headlining assembly (roof antenna cord).
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A-2 - B-2	Always	Below 1 Ω
   A-2a - B-2a	Always	Below 1 Ω
   A-2 or B-2 - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY). Refer to  REMOVAL [08/2019 - ] 

Result: 

OK 

See step  3

1. Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (to No. 2 Antenna Cord Sub-assembly)
   *b	Component without harness connected (to Antenna Cord Sub-assembly)

2. Disconnect the antenna connector from the antenna cord sub-assembly.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   B-2 - C-2	Always	Below 1 Ω
   B-2a - C-2a	Always	Below 1 Ω
   B-2 or C-2 - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE TELEPHONE AND GPS ANTENNA CORD (ROOF HEADLINING ASSEMBLY [ROOF ANTENNA CORD]). Refer to  REMOVAL [08/2019 - ] 

Result: 

OK 

See step  4

1. Disconnect the antenna connector from the roof headlining assembly (roof antenna cord).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (to Roof Headlining Assembly [Roof Antenna Cord])
   *b	Component without harness connected (to DCM [Telematics Transceiver])

2. Disconnect the antenna connector from the DCM (telematics transceiver).
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C-2 - D-1 (GPS)	Always	Below 1 Ω
   C-2a - D-1a (GND)	Always	Below 1 Ω
   C-2 or D-1 (GND) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE TELEPHONE AND GPS ANTENNA CORD (ANTENNA CORD SUB-ASSEMBLY). Refer to  REMOVAL [08/2019 - ] 

Result: 

OK 

See step  5

1. Replace the telephone and GPS antenna (for Roof Side) with a known good one.

   Refer to REMOVAL [08/2019 - ]

2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [08/2019 - ]

3. Recheck for DTCs and check that no DTCs are output.

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (TELEPHONE AND GPS ANTENNA [FOR ROOF SIDE] IS DEFECTIVE) 

Result: 

NG 

See step  6

1. Replace the DCM (telematics transceiver) with a new one.

   Refer to REMOVAL [08/2019 - ]

   NOTE:

   • The engine switch must be off.
   • Do not exchange the DCM (telematics transceiver) with one from another vehicle.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

PERFORM DCM ACTIVATION. Refer to  DCM ACTIVATION [08/2019 - ]