LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> RAV4 XLE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 132 (Engine Mechanical System (A25A-FXS) - Service Information (2 Of 6)) >> Engine Assembly >> Removal [11/2018 - 02/2019] >> Caution / Notice / Hint

Caution / Notice / Hint

WARNING: This page is about a different variant/trim than selected.

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

NECESSARY PROCEDURE AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system Refer to INITIALIZATION [11/2018 - 12/2021]
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system Refer to INITIALIZATION [11/2018 - 10/2022]
Panoramic view monitor system (for HV model) Refer to INITIALIZATION [11/2018 - 10/2022]
Reset back door close position Power back door system (for HV model) Refer to INITIALIZATION [11/2018 - 10/2023]
Back door lock initialization Power door lock control system Refer to INITIALIZATION [11/2018 - ]
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC P0630-51 is output Refer to REGISTRATION [11/2018 - 08/2020]
  • Replacement of engine assembly
  • Gas leak from exhaust system is repaired
  • Replacement of air fuel ratio sensor (sensor 2)
 Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc.
 Refer to INITIALIZATION [11/2018 - 08/2020]
Replacement of inverter with converter assembly Resolver learning
  • DTCs are stored
  • Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
  • Shock or vibration during acceleration
 Refer to UTILITY [11/2018 - 08/2020]
Replacement of hybrid vehicle transaxle assembly
  • Resolver learning
  • Initialize resolver
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)		 Television camera assembly optical axis (Back camera position setting) Parking assist monitor system Refer to CALIBRATION [11/2018 - 10/2022]
  • Parking assist ECU initialization
  • Adjust steering angle
 Panoramic view monitor system (for HV model) Refer to CALIBRATION [11/2018 - 10/2022]
Replacement of headlight ECU sub-assembly LH
  • Synchronize the vehicle information
  • Perform headlight ECU sub-assembly LH initialization
 Lighting system (EXT) (w/ Headlight ECU) Refer to INITIALIZATION [11/2018 - 12/2021]
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)		 Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment
  1. Clear the zero point calibration data and stored linear solenoid valve calibration data.
  2. Perform initialization and calibration of the linear solenoid valve.
  3. Perform yaw rate and acceleration sensor zero point calibration.
  • DTCs are stored
  • ABS warning light illuminates
  • Brake warning light / yellow (minor malfunction) illuminates
  • Slip indicator light illuminates
  • VSC disabled or malfunctions
 Refer to UTILITY [11/2018 - 02/2019]
Front bumper assembly (Including removal and installation) Front television camera view adjustment Panoramic view monitor system (for HV model) Refer to CALIBRATION [11/2018 - 10/2022]
NOTE:
  • After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
    WAITING TIME BEFORE DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL

    System Name See Procedure
    Vehicle enrolled in Toyota Entune system or safety connect system 6 minutes
    Vehicle not enrolled in Toyota Entune system and safety connect system 1 minute
  • This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

    Refer to PRECAUTION [11/2018 - ]

scientia non olet · About LEMON Manuals