- REMOVE FRONT WHEEL
Refer to REMOVAL [11/2018 - ]
- REMOVE FRONT FENDER FRONT SPLASH SHIELD RH (for Long Type)
- Remove the 4 screws.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- Detach the claw and remove the front fender front splash shield RH.
- REMOVE FRONT FENDER FRONT SPLASH SHIELD RH (for Short Type)
- Remove the 3 screws.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- Detach the claw and remove the front fender front splash shield RH.
- REMOVE FRONT FENDER MUDGUARD RH (w/ Mudguard)
- for Short Type:
HINT:
Use the same procedure described for the LH side.
Refer to PROCEDURE - Step 1
- for Long Type:
HINT:
Use the same procedure described for the LH side.
Refer to PROCEDURE - Step 3
- REMOVE NO. 1 ENGINE UNDER COVER
Refer to PROCEDURE - Step 10 [11/2018 - 10/2019]
, or refer to PROCEDURE - Step 10 [10/2019 - 08/2020]
- REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH (except Off Road Package)
HINT:
Use the same procedure described for the LH side.
Refer to PROCEDURE - Step 1
- REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH (for Off Road Package)
HINT:
Use the same procedure described for the LH side.
Refer to PROCEDURE - Step 2
- REMOVE FRONT FENDER LINER RH
- w/ Mudguard:
- Remove the 8 clips and 2 screws.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
| *A |
w/o Mudguard |
- |
- |
 |
Clip |
 |
Screw |
- w/o Mudguard:
- Remove the 9 clips and 2 screws.
- Using a screwdriver with its tip wrapped with protective tape, detach the claw and remove the 4 grommets.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- Remove the front fender liner RH.
- DRAIN WINDSHIELD WASHER FLUID
- Disconnect the washer hose from the windshield washer motor and pump assembly, and drain the washer fluid.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
HINT:
Use a container to collect the washer fluid.
- REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
- Disconnect the washer hose from the windshield washer motor and pump assembly.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
 |
Remove in this Direction |
 |
Washer hose |
 |
Connector |
- Disconnect the connector.
- Remove the windshield washer motor and pump assembly as shown in the illustration.
- REMOVE FRONT BUMPER COVER
- except Off Road Package:
Refer to REMOVAL [11/2018 - 02/2019]
, or refer to REMOVAL [02/2019 - 08/2020]
- for Off Road Package:
Refer to REMOVAL [11/2018 - 02/2019]
, or refer to REMOVAL [02/2019 - 08/2020]
- REMOVE WASHER INLET SUB-ASSEMBLY
- Remove the clip.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
 |
Place Hand Here |
 |
Remove in this Direction |
- Place your hands at the position shown in the illustration and remove the washer inlet sub-assembly in the direction indicated by the arrow.
- REMOVE WINDSHIELD WASHER JAR ASSEMBLY
- Detach the clamp and disconnect the washer hose.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- Detach the clamp.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
| *A |
w/ Level Warning Switch |
- w/ Level Warning Switch:
- Disconnect the connector.
- Remove the 3 bolts. Then detach the guide and remove the windshield washer jar assembly.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
|
- REMOVE LEVEL WARNING SWITCH ASSEMBLY (w/ Level Warning Switch)
See step 3 [11/2018 - 02/2019], or see step 3 [02/2019 - ]