LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Prius XLE AWD-e >> Repair and Diagnosis >> External Pages >> Different car >> Section 262 (Meter / Gauge / Display - Diagnostic Codes (B1321-B1508) (Except Hybrid)) >> METER / GAUGE SYSTEM (for Gasoline Model) >> On-Vehicle Inspection [08/2021 - ] >> Procedure

On-Vehicle Inspection [08/2021 - ]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Avalon, 2021 Toyota Avalon, 2020 Toyota Avalon, and 2019 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT COMBINATION METER ASSEMBLY 
    1. Inspect speedometer operation
      NOTE:
      • The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake actuator assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake actuator assembly) because it is the source of the vehicle speed signal.
      • Data List values of the skid control ECU (brake actuator assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
      1. Warm up the engine.
      2. Connect the Techstream to the DLC3.
      3. Turn the engine switch on (IG).
      4. Turn the Techstream on.
      5. Enter the following menus: Chassis / Brake/EPB / Data List.
      6. Read the Data List according to the display on the Techstream.

        Chassis > Brake/EPB 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

        Chassis > Brake/EPB > Data List 

        Tester Display
        Vehicle Speed
        REFERENCE MPH (FOR SPEEDOMETER WITH IMPERIAL UNITS FOR MAIN SCALE)

        Techstream Indication (mph) Acceptable Range (mph)
        20 19.2 to 21.7
        40 39.4 to 42.2
        60 59.8 to 62.6
        80 80.0 to 83.2
        100 100.5 to 103.7
        120 120.9 to 124.1
        140 141.3 to 144.5
        REFERENCE KM/H (FOR SPEEDOMETER WITH METRIC UNITS FOR MAIN SCALE)

        Techstream Indication (km/h) Acceptable Range (km/h)
        20 18.5 to 22.5
        40 38.7 to 43.2
        60 59.2 to 63.7
        80 79.3 to 84.3
        100 99.8 to 104.8
        120 120.3 to 125.3
        140 140.7 to 145.7
        160 161.2 to 166.2
        180 181.6 to 186.6
        200 202.1 to 207.1
        220 222.5 to 227.5
        240 243.0 to 248.0

        OK

        Speedometer reading is within the acceptable range at each vehicle speed.

    2. Inspect tachometer operation
      1. Warm up the engine.
      2. Connect the Techstream to the DLC3.
      3. Turn the engine switch on (IG).
      4. Enter the following menus: Powertrain / Engine / Data List.
      5. Read the Data List according to the display on the Techstream.

        Powertrain > Engine > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 650 to 750 rpm: Idling (shift lever in N, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

        Powertrain > Engine > Data List 

        Tester Display
        Engine Speed
        REFERENCE

        Techstream Indication (rpm) Acceptable Range (rpm)
        Data in () is for Reference
        700 630 to 770
        1000 (900 to 1100)
        2000 (1850 to 2150)
        3000 2800 to 3200
        4000 (3800 to 4200)
        5000 4800 to 5200
        6000 (5750 to 6250)
        7000 6700 to 7300

        OK

        Tachometer reading is within the acceptable range at each engine speed.

    3. Check LED illumination (LED check)
      1. Check the illumination function of the warning or indicator lights listed below when turning the engine switch on (IG).

        OK

        Warning or Indicator Light Specified Condition
        Brake warning light / red (malfunction) Warning or indicator light comes on for about 3 seconds after turning the engine switch on (IG).
        Slip indicator light
        VSC OFF indicator light
        ABS warning light
        Tire pressure warning light
        Master warning light
        ICS OFF indicator light*
        Brake warning light / yellow (minor malfunction)
        Brake hold standby indicator light
        Brake hold operated indicator light
        PCS warning light
        SRS warning light Warning light comes on for about 6 seconds after turning the engine switch on (IG).
        EPS warning light When the engine switch is turned on (IG), warning light (red) illuminates for 2 seconds and then the warning light (yellow) illuminates.
        MIL (Check engine warning light) Warning light comes on when the engine switch on (IG).
        1. *: w/ Intelligent Clearance Sonar System
scientia non olet · About LEMON Manuals