| C1247/47 |
Stroke Sensor Malfunction |
211
212
213
214
215
216
217
218
219
220
221
222
223 |
- INF Code: 211
- Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.
- INF Code: 212
- Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.
- INF Code: 213
- Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more.
- INF Code: 214
- Either of the following is detected:
- Fluctuation of sensor output 1 (SKS1) is out of specification.
- The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.
- INF Code: 215
- Either of the following is detected:
- Fluctuation of sensor output 2 (SKS2) is out of specification.
- The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more.
- INF Code: 216
- Either of the following is detected:
- Pedal off position (zero point stored value) is out of specification.
- The zero point stored value for the sensor output voltage 1 (SKS1) is deviates -17% to 25.9% (0.15 to 2.3 V) or more from the theoretical value.
- INF Code: 217
- Either of the following is detected:
- Pedal off position (zero point stored value) is out of specification.
- The zero point stored value for the sensor output voltage 2 (SKS2) deviates -31.7% to 17% (2.42 to 4.85 V) or more from the theoretical value.
- INF Code: 218
- An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more.
- INF Code: 219
- INF Code: 220
- The sum of sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) deviates 15% or more from the theoretical value 5 V.
- INF Code: 221
- An excessive difference exists between the variation in sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2).
- INF Code: 222
- Sensor power source voltage (VCM1) remains at 4.75 V or less or 5.25 V or more and the sensor data is invalid for 0.2 seconds or longer.
- INF Code: 223
- Sensor data is invalid for 0.2 seconds or more.
(Open, short or noise.)
|
- INF Code: 211
- Open or short in brake pedal stroke sensor assembly power supply circuit
- Improperly connected connector, deformation or corrosion of terminals
- Skid control ECU (Brake booster with master cylinder assembly)
- INF Code: 212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 223
- Open or short in wire harness
- Improperly connected connector, deformation or corrosion of terminals
- Brake pedal stroke sensor assembly
|
Electronically controlled brake system DTC |
| C1346/71 |
Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC) |
- |
Detected only during Test Mode. |
- Brake pedal stroke sensor assembly
- Brake pedal stroke sensor assembly circuit
|
Electronically controlled brake system Test Mode DTC |
| C1392/48 |
Stroke Sensor Zero Point Calibration Undone |
- |
Zero point calibration of brake pedal stroke sensor assembly is unfinished. |
- Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)
- Skid control ECU (Brake booster with master cylinder assembly)
|
Electronically controlled brake system DTC |