DTC B15C0: Short in GPS Antenna; DTC B15C1: Open in GPS Antenna [12/2013 - ]: Procedure

1. Turn the engine switch off.
2. Connect the Techstream to the DLC3.
3. Turn the engine switch on (IG) and wait for 10 seconds.
4. Turn the Techstream on.
5. Perform "HEALTH CHECK" and check for current DTCs.

   Refer to HEALTH CHECK [12/2013 - ]

   Result

   Result	Proceed to
   DTC B15C0 or B15C1 is output	A
   DTC B15C0 or B15C1 is not output	B

Result:  2

B 

CHECK FOR INTERMITTENT PROBLEMS. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - 11/2016]  Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2016 - ] 

Result:  1

A 

See step  2

1. Disconnect the telephone and GPS antenna cord (floor wire) connector from the DCM (Telematics Transceiver).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Telephone and GPS Antenna Cord (Floor Wire)

2. Disconnect the telephone and GPS antenna cord (floor wire) connector from the telephone and GPS antenna cord (No. 3 antenna cord sub-assembly).
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L28-1 - L27-1 (GPS)	Always	Below 1 Ω
   L28-1 or L27-1 (GPS) - Body ground	Always	10 kΩ or higher
   L28-1a - L27-1a	Always	Below 1 Ω
   L28-1a or L27-1a - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPLACE TELEPHONE AND GPS ANTENNA CORD (FLOOR WIRE) 

Result:  1

OK 

See step  3

1. Disconnect the telephone and GPS antenna cord (No. 3 antenna cord sub-assembly) connector from the telephone and GPS antenna assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Telephone and GPS Antenna Cord (No. 3 Antenna Cord Sub-assembly)

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A-2 - L28-1	Always	Below 1 Ω
   A-2 or L28-1 - Body ground	Always	10 kΩ or higher
   A-2a - L28-1a	Always	Below 1 Ω
   A-2a or L28-1a - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY). Refer to  REMOVAL [12/2013 - ] 

Result:  1

OK 

See step  4

1. Replace the telephone and GPS antenna assembly with a known good one and check if the same problem occurs again.

   Refer to REMOVAL [12/2013 - ]

   OK

   The system returns to normal.

   Result

   Proceed to
   OK
   NG

Result:  1

OK 

END 

Result:  2

NG 

See step  5

1. Replace the DCM (Telematics Transceiver).

   Refer to REMOVAL [12/2013 - 11/2016] Refer to REMOVAL [11/2016 - ]

   NOTE:

   • The engine switch must be off.
   • Do not swap the DCM (Telematics Transceiver) with one from another vehicle.

NEXT 

1. Perform "PRL UPDATE".

   Refer to PRL UPDATE [12/2013 - ]

NEXT 

PERFORM DCM ACTIVATION. Refer to  DCM ACTIVATION [12/2013 - ]