Installation [12/2013 - 11/2016]: Procedure

1. for 1AR-FE:
   1. Install the 14 hole plugs to the front frame assembly.

      HINT: 

      There are 4 different shapes of hole plug.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. for 2GR-FE:
   1. Install the 10 hole plugs to the front frame assembly.

      HINT: 

      There are 2 different shapes of hole plug.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath
   	Front of the Vehicle

   NOTE:

   Position the front suspension member body mounting rear cushion LH in the correct direction.

2. Install SST as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Front Suspension Member Body Mounting Rear Cushion LH

   • SST: 09830-10010 
     1. 09830-01010
     2. 09830-01020
     3. 09830-01030
     4. 09830-01060
3. Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Hold
   *b	Turn

   NOTE:

   Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion LH.

1. Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath
   	Front of the Vehicle

   NOTE:

   Position the front suspension member body mounting rear cushion RH in the correct direction.

2. Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.
   • SST: 09830-10010 
     1. 09830-01010
     2. 09830-01020
     3. 09830-01030
     4. 09830-01060
3. Using SST, install the front suspension member body mounting rear cushion RH.
   • SST: 09830-10010 
     1. 09830-01010
     2. 09830-01020
     3. 09830-01030
     4. 09830-01060

   HINT: 

   Perform the same procedure as for the LH side.

1. Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View from Underneath
   	Front of the Vehicle

   NOTE:

   Position the front suspension member body mounting front cushion in the correct direction.

2. Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.
   • SST: 09830-10010 
     1. 09830-01010
     2. 09830-01020
     3. 09830-01030
     4. 09830-01060
3. Using SST, install each front suspension member body mounting front cushion as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Hold
   *b	Turn

   • SST: 09830-10010 
     1. 09830-01010
     2. 09830-01020
     3. 09830-01030
     4. 09830-01060
   NOTE:

   Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.

1. Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.

1. Install the 2 front suspension member body mounting front stoppers to the front frame assembly.

1. Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.

   Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. for 2WD:
   1. Install the No. 2 frame crossmember dynamic damper to the front frame assembly with the 2 bolts.

      Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf) 

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. for AWD:
   1. Install the No. 2 frame crossmember dynamic damper to the front frame assembly with the 2 bolts.

      Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf) 

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Bolt 1, 2 

   Torque: 200 N*m (2039 kgf*cm, 148 ft.*lbf) 

   Bolt 3 

   Torque: 135 N*m (1377 kgf*cm, 100 ft.*lbf) 

   NOTE:

   Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 3

1. Install the front stabilizer bar with 2 front No. 2 stabilizer brackets, 2 front No. 1 stabilizer bar bushings and 2 front stabilizer link assemblies to the front frame assembly.

See step  5

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 14

for 1AR-FE: Refer to PROCEDURE - Step 8 (INSTALLATION [12/2013 - 11/2016])

for 2GR-FE: Refer to PROCEDURE - Step 12 (INSTALLATION [12/2013 - 11/2016])

for 1AR-FE: Refer to PROCEDURE - Step 9 (INSTALLATION [12/2013 - 11/2016])

for 2GR-FE: Refer to PROCEDURE - Step 13 (INSTALLATION [12/2013 - 11/2016])

Refer to PROCEDURE - Step 7 (INSTALLATION [12/2013 - 11/2016])

Refer to PROCEDURE - Step 11 (INSTALLATION [12/2013 - 11/2016])

for 1AR-FE: Refer to PROCEDURE - Step 10 (INSTALLATION [12/2013 - 11/2016])

for 2GR-FE: Refer to PROCEDURE - Step 15 (INSTALLATION [12/2013 - 11/2016])