Components [11/2016 - ]: Illustration
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (1 Of 7)
| Callout | Description | Callout | Description |
| *1 | OUTER COWL TOP PANEL SUB-ASSEMBLY | *2 | BRAKE BOOSTER VACUUM EJECTOR |
| N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (2 OF 7)
| Callout | Description | Callout | Description |
| *1 | COOL AIR INTAKE DUCT SEAL | *2 | FRONT FENDER APRON SEAL LH |
| *3 | FRONT FENDER APRON SEAL RH | *4 | FRONT FENDER LINER LH |
| *5 | FRONT FENDER LINER RH | *6 | FRONT FLOOR COVER LH |
| *7 | NO. 1 ENGINE UNDER COVER | *8 | NO. 2 ENGINE UNDER COVER |
| *9 | RADIATOR SIDE DEFLECTOR SEAL LH | *10 | RADIATOR SIDE SEAL RH |
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (3 Of 7)
| Callout | Description | Callout | Description |
| *1 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *4 | BATTERY |
| *5 | BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY | *6 | ENGINE WIRE |
| *7 | INLET AIR CLEANER ASSEMBLY | *8 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *9 | BATTERY CLAMP | *10 | BATTERY TRAY |
| *11 | BATTERY CLAMP BOLT | - | - |
| N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (4 Of 7)
| Callout | Description | Callout | Description |
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
| *3 | FRONT STABILIZER LINK ASSEMBLY LH | *4 | STEERING INTERMEDIATE SHAFT ASSEMBLY |
| *5 | STEERING LINK ASSEMBLY | *6 | TIE ROD ASSEMBLY LH |
| *7 | COTTER PIN | *8 | GASKET |
| *9 | WINDSHIELD WASHER JAR ASSEMBLY | - | - |
| N*m (kgf*cm, ft.*lbf): Specified torque | • | Non-reusable part |
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (5 Of 7)
| Callout | Description | Callout | Description |
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR RH |
| *3 | FRONT ENGINE MOUNTING INSULATOR | *4 | FRONT FRAME ASSEMBLY |
| *5 | HOLE PLUG | *6 | NO. 2 ENGINE MOUNTING STAY RH |
| *7 | FRAME SIDE RAIL PLATE LH | *8 | FRAME SIDE RAIL PLATE RH |
| *9 | FRONT SUSPENSION MEMBER REAR BRACE LH | *10 | FRONT SUSPENSION MEMBER REAR BRACE RH |
| N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (6 Of 7)
| Callout | Description | Callout | Description |
| *1 | FRONT FRAME ASSEMBLY | *2 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
| *3 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH | *4 | FRONT NO. 1 STABILIZER BRACKET LH |
| *5 | FRONT NO. 1 STABILIZER BRACKET RH | *6 | FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY |
| *7 | STEERING LINK ASSEMBLY | - | - |
| N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Fig 1: Front Suspension Member Replacement Component With Torque Specifications (For 1AR-FE) (7 Of 7)
| Callout | Description | Callout | Description |
| *1 | FRONT FRAME ASSEMBLY | *2 | FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION |
| *3 | FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER | *4 | FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH |
| *5 | FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH | *6 | FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER |
| *7 | FRONT SUSPENSION MEMBER DYNAMIC DAMPER | *8 | HOLE PLUG |
| N*m (kgf*cm, ft.*lbf): Specified torque | • | Non-reusable part |