Problem Symptoms Table [12/2013 - ]

WARNING: This page is about a different variant/trim than selected.

HINT:

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.

SFI SYSTEM:

Symptom	Suspected Area	Link
Engine does not crank (Does not start)	Battery	Refer to PROCEDURE - Step 1
	Starter assembly	Refer to INSPECTION [12/2013 - ]
	Park/Neutral position switch assembly	Refer to INSPECTION [12/2013 - ]
	VC output circuit (ECM 5 V circuit)	Refer to VC Output Circuit [12/2013 - ]
	Starter signal circuit	Refer to Starter Signal Circuit [12/2013 - 11/2016] Refer to Starter Signal Circuit [11/2016 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
No initial combustion (Does not start)	Immobilizer system	Refer to PROBLEM SYMPTOMS TABLE [12/2013 - ]
	VC output circuit (ECM 5 V output)	Refer to VC Output Circuit [12/2013 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
	Crankshaft position sensor	Refer to INSPECTION [12/2013 - ]
	Camshaft position sensor (for intake camshaft)	Refer to DTC P0340: Camshaft Position Sensor Circuit; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) [12/2013 - 11/2016] Refer to DTC P0340: Camshaft Position Sensor Circuit; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) [11/2016 - ]
	Camshaft position sensor (for exhaust camshaft)	Refer to DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1) [12/2013 - 11/2016] Refer to DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1) [11/2016 - 10/2017] Refer to DTC P0365: Camshaft Position Sensor "B" Circuit (Bank 1); DTC P0367: Camshaft Position Sensor "B" Circuit Low Input (Bank 1); DTC P0368: Camshaft Position Sensor "B" Circuit High Input (Bank 1) [10/2017 - ]
	Valve timing	Refer to PROCEDURE - Step 5 Refer to PROCEDURE - Step 5 Refer to PROCEDURE - Step 5
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Fuel injector circuit	Refer to Fuel Injector Circuit [12/2013 - ]
	Starter signal circuit	Refer to Starter Signal Circuit [12/2013 - 11/2016] Refer to Starter Signal Circuit [11/2016 - ]
	No. 1 valve rocker arm sub-assembly*	Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]
Engine cranks normally but difficult to start	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Engine coolant temperature sensor	Refer to INSPECTION [12/2013 - ]
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Compression	Refer to PROCEDURE - Step 11
	Fuel injector assembly	Refer to INSPECTION [12/2013 - ]
	Fuel injector circuit	Refer to Fuel Injector Circuit [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Throttle body with motor assembly	Refer to INSPECTION [12/2013 - ]
	PCV valve and hose	Refer to COMPONENTS [12/2013 - ]
	Starter signal circuit	Refer to Starter Signal Circuit [12/2013 - 11/2016] Refer to Starter Signal Circuit [11/2016 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
	No. 1 valve rocker arm sub-assembly*	Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]
Incomplete intermittent combustion occurs (Does not start)	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Fuel pump	Refer to INSPECTION [12/2013 - ]
	Fuel line	-
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Fuel injector circuit	Refer to Fuel Injector Circuit [12/2013 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
	Starter signal circuit	Refer to Starter Signal Circuit [12/2013 - 11/2016] Refer to Starter Signal Circuit [11/2016 - ]
	Crankshaft position sensor	Refer to INSPECTION [12/2013 - ]
	Valve timing	Refer to PROCEDURE - Step 5 Refer to PROCEDURE - Step 5 Refer to PROCEDURE - Step 5
High engine speed	Throttle body with motor assembly	Refer to INSPECTION [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	A/C signal circuit	Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
	Engine coolant temperature sensor	Refer to INSPECTION [12/2013 - ]
	PCV valve and hose	Refer to COMPONENTS [12/2013 - ]
Low engine speed (Poor idle)	Throttle body with motor assembly	Refer to INSPECTION [12/2013 - ]
	A/C signal circuit	Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ]
	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Fuel pump	Refer to INSPECTION [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	PCV valve and hose	Refer to COMPONENTS [12/2013 - ]
Rough idle	Compression	Refer to PROCEDURE - Step 11
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Spark plug	Refer to PROCEDURE - Step 3
	Fuel injector circuit	Refer to Fuel Injector Circuit [12/2013 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Fuel pump	Refer to INSPECTION [12/2013 - ]
	Fuel line	-
	Throttle body with motor assembly	Refer to INSPECTION [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Purge VSV	Refer to INSPECTION [12/2013 - ]
	PCV valve and hose	Refer to COMPONENTS [12/2013 - ]
	Air fuel ratio sensor	Refer to INSPECTION [12/2013 - ]
	Heated oxygen sensor	Refer to INSPECTION [12/2013 - ]
	Mass air flow meter sub-assembly	Refer to INSPECTION [12/2013 - ]
	Knock control sensor	Refer to INSPECTION [12/2013 - ]
	No. 1 valve rocker arm sub-assembly*	Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]
	External part malfunction (Increase in load: A/C system, etc.)	-
Hunting (Poor idle)	Throttle body with motor assembly	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	ECM power source circuit	Refer to ECM Power Source Circuit [12/2013 - ]
	ACIS control circuit	Refer to ACIS Control Circuit [12/2013 - 11/2016] Refer to ACIS Control Circuit [11/2016 - ]
	Intake air control valve actuator (for tumble control valve)	Refer to PROCEDURE - Step 3
Hesitation and/or poor acceleration (Poor driveability)	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Spark plug	Refer to PROCEDURE - Step 3
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Fuel injector assembly	Refer to INSPECTION [12/2013 - ]
	Mass air flow meter sub-assembly	Refer to INSPECTION [12/2013 - ]
	Throttle body with motor assembly	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Compression	Refer to PROCEDURE - Step 11
	Brake override system	Refer to Brake Override System [12/2013 - 11/2016] Refer to Brake Override System [11/2016 - ]
	No. 1 valve rocker arm sub-assembly*	Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]
Surging (Poor driveability)	Spark plug	Refer to PROCEDURE - Step 3
	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Fuel injector assembly	Refer to INSPECTION [12/2013 - ]
	Mass air flow meter sub-assembly	Refer to INSPECTION [12/2013 - ]
	Variable Valve Timing (VVT) system	Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [12/2013 - 08/2014] Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [08/2014 - 11/2015] Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [11/2015 - 11/2016] Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [11/2016 - ]
	Compression	Refer to PROCEDURE - Step 11
	No. 1 valve rocker arm sub-assembly*	Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]
Engine stalls soon after starting	Immobilizer system	Refer to PROBLEM SYMPTOMS TABLE [12/2013 - ]
	Fuel pump control circuit	Refer to Fuel Pump Control Circuit [12/2013 - 11/2016] Refer to Fuel Pump Control Circuit [11/2016 - ]
	Spark plug	Refer to PROCEDURE - Step 3
	Ignition system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Fuel injector assembly	Refer to INSPECTION [12/2013 - ]
	Variable Valve Timing (VVT) system	Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [12/2013 - 08/2014] Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [08/2014 - 11/2015] Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [11/2015 - 11/2016] Refer to DTC P0016: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A); DTC P0017: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) [11/2016 - ]
	Throttle body with motor assembly	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	Intake system	Refer to ON-VEHICLE INSPECTION [12/2013 - ]
	PCV valve and hose	Refer to COMPONENTS [12/2013 - ]
	Compression	Refer to PROCEDURE - Step 11
	No. 1 valve rocker arm sub-assembly*	Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]
Engine stalls only during A/C operation	A/C signal circuit	Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ]
Engine stalls only during A/C operation	ECM	Refer to TERMINALS OF ECM [12/2013 - 11/2016] Refer to TERMINALS OF ECM [11/2016 - ]
SNOW mode does not change	Pattern select switch snow mode circuit	Refer to Pattern Select Switch Snow Mode Circuit [12/2013 - 11/2016] Refer to Pattern Select Switch Snow Mode Circuit [11/2016 - ]
Unable/difficult to refuel	Fuel system (canister, refueling valve, roll over valve, fuel tank, etc.)	-

HINT:

*: Check "Fuel Cut Elps Time" in the Data List. If the elapsed time is over 0 sec, then the engine speed is high (the engine speed at which fuel cut occurs + 500 rpm or more). In this situation, there is a possibility that a No. 1 valve rocker arm sub-assembly will become loose and malfunction, check that the No. 1 valve rocker arm sub-assemblies are properly installed.

Refer to COMPONENTS [12/2013 - 11/2015] Refer to COMPONENTS [11/2015 - ]