LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Highlander Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 8 (Fuel System (2GR-FE) (Service Information) (Except Hybrid)) >> Fuel Pump Ecu >> Installation [12/2013 - 11/2016] >> Procedure

Installation [12/2013 - 11/2016]: Procedure

WARNING: This page is about a different car, the 2016 Toyota Highlander, 2015 Toyota Highlander, and 2014 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL FUEL PUMP CONTROL ECU ASSEMBLY 
    1. Install the fuel pump control ECU assembly with the 2 nuts.

      Torque: 8.0 N*m ( 82 kgf*cm, 71 in.*lbf)  

    2. Connect the fuel pump control ECU assembly connector.
  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH 

    Refer to PROCEDURE - Step 23 , or refer to PROCEDURE - Step 24

  3. INSTALL ROPE HOOK (for LH Side) 

    Refer to PROCEDURE - Step 24 , or refer to PROCEDURE - Step 25

  4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side) 

    Refer to PROCEDURE - Step 25 , or refer to PROCEDURE - Step 26

  5. INSTALL DECK TRIM POCKET COVER (for LH Side) 

    Refer to PROCEDURE - Step 26 , or refer to PROCEDURE - Step 27

  6. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 11 , or refer to PROCEDURE - Step 11

  7. INSTALL NO. 2 DECK SIDE TRIM COVER 

    Refer to PROCEDURE - Step 29 , or refer to PROCEDURE - Step 30

  8. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 14 , or refer to PROCEDURE - Step 14

  9. INSTALL FRONT DECK SIDE TRIM COVER LH 

    Refer to PROCEDURE - Step 31 , or refer to PROCEDURE - Step 32

  10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 49 , or refer to PROCEDURE - Step 50

  11. INSTALL REAR DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 50 , or refer to PROCEDURE - Step 51

  12. INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH 

    Refer to PROCEDURE - Step 4

  13. INSTALL REAR NO. 2 SEAT ASSEMBLY 

    Refer to INSTALLATION [12/2013 - 11/2016]

  14. INSTALL REAR FLOOR FINISH PLATE 

    Refer to PROCEDURE - Step 67 , or refer to PROCEDURE - Step 68

  15. INSTALL REAR DECK FLOOR BOX 

    Refer to PROCEDURE - Step 68 , or refer to PROCEDURE - Step 69

  16. INSTALL DECK SIDE TRIM BOX LH 

    Refer to PROCEDURE - Step 69 , or refer to PROCEDURE - Step 70

  17. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 70 , or refer to PROCEDURE - Step 71

  18. INSTALL DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 71 , or refer to PROCEDURE - Step 72

  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [12/2013 - 11/2016]

scientia non olet · About LEMON Manuals