LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Highlander Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 30 (Automatic Transmission (U660E) - Service Information (1 Of 2)) >> Park / Neutral Position Switch >> Installation [12/2013 - 11/2016] >> Procedure

Installation [12/2013 - 11/2016]: Procedure

WARNING: This page is about a different car, the 2016 Toyota Highlander, 2015 Toyota Highlander, and 2014 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Move the shift lever to N.
    2. Align the protrusions of the park/neutral position switch assembly.
      GTY429638Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protrusion
    3. Install the park/neutral position switch assembly to the manual valve lever shaft sub-assembly with the 2 bolts.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      NOTE:
      • Before installing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to install the park/neutral position switch assembly straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.
      • After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.
    4. Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the nut and washer.

      Torque: 12.7 N*m (130 kgf*cm, 9 ft.*lbf) 

    5. Connect the connector to the park/neutral position switch.
  2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Install a new clip to the No. 1 transmission control cable bracket.
    2. Install the transmission control cable assembly to the No. 1 transmission control cable bracket.
      GTY432378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw A
      *b Claw B
      *c Transmission Control Cable Assembly
      NOTE:
      • Make sure that the claws A on the clip are securely fit into the No. 1 transmission control cable bracket holes.
      • Make sure that the transmission control cable assembly is securely installed inside of the claws B of the clip.
    3. Install the transmission control cable assembly to the transmission control shaft lever with the nut.

      Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf) 

      NOTE:

      Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.

    4. Engage wire harness clamp to the wire harness clamp bracket.
  3. INSTALL AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 54

  4. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 55

  5. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 3

  6. INSTALL INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 57

  7. INSTALL COOL AIR INTAKE DUCT SEAL 

    Refer to PROCEDURE - Step 4

  8. INSTALL RADIATOR SIDE SEAL RH 

    Refer to PROCEDURE - Step 5

  9. INSTALL RADIATOR SIDE DEFLECTOR SEAL LH 

    Refer to PROCEDURE - Step 6

  10. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION 

    See step  1

  11. INSPECT SHIFT LEVER POSITION 

    See step  1

  12. ADJUST SHIFT LEVER POSITION 

    Refer to ADJUSTMENT [12/2013 - 11/2016] 

scientia non olet · About LEMON Manuals