Removal [12/2013 - 11/2016]: Procedure

for 1AR-FE: Refer to PROCEDURE - Step 3

for 2GR-FE: Refer to PROCEDURE - Step 4

1. Disengage the 2 claws and separate the sensor clamp.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Sensor Clamp

2. Remove the bolt and separate the front speed sensor from the steering knuckle.
   NOTE:

   • Prevent foreign matter from contacting the sensor tip.
   • Be careful not to damage the front speed sensor.
   • Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.

See step  2

Refer to PROCEDURE - Step 12

for 2WD: Refer to PROCEDURE - Step 6

for AWD: Refer to PROCEDURE - Step 5

1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Matchmark

2. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
   NOTE:

   Be careful not to damage the drive shaft boot.

   HINT: 

   If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.

1. Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   NOTE:

   • When removing the nuts, keep the bolts from rotating.
   • Be careful not to damage the drive shaft boot or speed sensor rotor.

1. Using a screwdriver with its tip wrapped with protective tape, remove the front No. 1 wheel bearing dust deflector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Protective Tape

   NOTE:

   Be careful not to damage the steering knuckle.

1. Using snap ring pliers, remove the front axle hub hole snap ring.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Secure the front axle assembly between aluminum plates in a vise.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   NOTE:

   Do not overtighten the vise.

2. Using SST, remove the front axle hub sub-assembly.
   • SST: 09520-00031 
3. Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   • SST: 09555-55010 
   • SST: 09950-60010 
     1. 09951-00440
   • SST: 09950-70010 
     1. 09951-07100
   NOTE:

   Be careful not to drop the front axle hub sub-assembly.

1. Remove the 4 bolts and front disc brake dust cover sub-assembly from the steering knuckle.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Place the bearing inner race (outside) on the front axle hub bearing.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Steel Plate
   *b	V-block

2. Using SST, a steel plate, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.
   • SST: 09950-60010 
     1. 09951-00440
     2. 09952-06010
   • SST: 09950-60020 
     1. 09951-00750
   • SST: 09950-70010 
     1. 09951-07100
   NOTE:

   Keep the steering knuckle level.